60 Days

Autel PowerScan PS100 Electrical System Scanner 12V/24V Car Auto Circuit Tester

  • Autor do post:
  • Post publicado:
  • Categoria do post:
  • Comentários do post:0 comentário

Autel Powerscan Ps100 Electrical System Tester Ps 100 Circuit Tester with 20ft Cable, Built-In Circuit Breaker, Easy to Read AC/DC Current Resistance, Test Continuity/Probe/Sensor Signal Autel PowerScan PS100---Revolutionary Circuit Tester Autel PowerScan PS100 Tool is the most revolutionary circuit tester to date. Featuring AVOmeter, test light, built-in flashlight, short circuit indicator, relay/ component tester, continuity tester and bad ground indicator, the PowerScan 100 is truly the ultimate in power and affordability, allowing users to check circuitry in one single step. Autel PS100 Car Circuit System Diagnostic Tool can quickly and accurately diagnose the electrical system, solve problems such as circuit short circuit, open circuit, etc., which is an essential circuit scanner for every technician. Autel PS100 Circuit Tester Kit--- Do Everything For You DC voltage range : 0-65V +1 digit; Resistance range : 0–200 KΩ; Frequency response of tone passage: 0Hz to 10Khz. Performs multi-service including power injection, measurement, ground testing, polarity checks, continuity testing and components activation Easy to read AVOmeter allows you to read voltage, current and resistance at the fingertip Component activation with a flip of the power switch, Instantly identifies positive, negative and open circuits Test bad ground contacts instantly, allowing you to follow and locate shorts fast without wasting fuses Instantly checks continuity of switches, relays and diodes Circuit breaker protected Extra 20ft (extendable) cable provides excellent accessibility to test along the vehicle Built-in Flashlight, work in the dark Simple button design More Useful Features, Give You Try Autel PowerScan PS100 has rich functions, please check the following introduction: 4 modes to diagnose the electrical system: DC voltage, AC voltage, resistance, diode. Voltage & Polarity Test: According to the LED light and sound after the probe tip touches the circuit, it can accurately judge the positive, negative, and open circuits. Continuity Test: While the tool is in Resistance mode, using the probe tip with chassis ground or the auxiliary ground lead, continuity can be tested on wires and components attached or disconnected from the vehicle’s electrical system. Signal Circuit Test: When the vehicle has a fault code, in order to quickly determine whether the fault is caused by a certain sensor circuit, you can use this tool to quickly draw a conclusion. Find Short Circuit: A short can manifest itself as a blown fuse or a tripped electrical protection device. Use the probe tip to activate and energize each fuse contact. The contacts that trip the circuit breaker are shorted. Find Bad Ground: Probe for suspected ground wires or touch probe tips. If the breaker has tripped, the circuit is most likely grounded. Activate Component in your hand/ in the vehicle/ W/Ground Test Trailer Lights and Connections: Check function and orientation of connectors and trailer lights Red/Green Polarity Indicator: The red/green polarity LED illuminates when the probe tip voltage matches and is within ±0.8 volts of the battery voltage. It is additional information that may be of value to a technician. DC Voltage While the tool in this mode, contact the probe tip to a circuit, then the LCD display will read the DC voltage with a resolution of 0.1 volt. AC Voltage While the tool in this mode, contact the probe tip to a circuit, then the LCD display will read the Max. voltage, the Min. voltage, frequency and duty cycle. Resistance While the tool in this mode, contact the probe tip to a circuit, then the LCD display will read the resistance between the tip and auxiliary ground lead. Tone On/ Off While the tool in this mode, just do a quick press of the mode button to toggle the tone on or off. While quickly pressing (a quick press and release) the mode button, if a short high beep is heard, this means the audio tone is turned on. If a short low beep is heard, the audio tone is turned off. Extra 20ft Extension Cable 20ft Extension Cable: Autel PS100 itself has an extra-long cable, but considering the volume of 12V-24v vehicles such as ships and trucks, we have additionally equipped with extra 20FT extension cable for emergencies. With the 20FT extension cable, you can freely test the condition of any vehicle circuit without moving the device because the cable is not long enough. Autel PS100 Circuit Tester has two power supply methods: 1. Vehicle battery power supply 2. Ciga-rette li-ghter power supply Quick Self-Test: Before you test a circuit or component, be sure your tool is in good order by doing a quick self-test. With the tool connected, perform a quick self-test. The power switch is a momentary rocker switch located on the tool's body. Flanking the switch are positive and negative markings. Press the Power Switch forward to activate the tip with a positive voltage. The Red LED should light and the LCD display will read the battery voltage. If the tone feature is turned on, a high pitched tone will sound. Let go of the power switch and the LED will turn off and the high tone will cease. Press the Power Switch rearward to activate the tip with a negative voltage. The Green LED should light and the LCD display will read the „0.0V‟ (ground). If the tone feature is turned on, a low pitched tone will sound. Let go of the power switch and the LED will turn off and the low tone will cease. Your tool is working correctly and is now ready for use. Test Tool Specifications DC voltage range 0-65V +1 digit Resistance range 0 – 200 KΩ Frequency response of tone 0Hz to 10Khz Circuit Breaker Rating current 1 – 10 Amp Display TFT color display (160 x 128 dpi) External Power 12.0 or 24.0 V power provided via vehicle battery Package including 1* PowerScan PS100 1* 20ft. extension cable 1* Rugged blow molded case 1*Probe tip 1* Battery clips 1*Ciga-rette lig-hter adapter 1*User's Manual On Jun 6, 2023 at 03:14:20 PDT, seller added the following information:

Continue lendoAutel PowerScan PS100 Electrical System Scanner 12V/24V Car Auto Circuit Tester

KZYEE KM50 Car PowerScan 12&24V Probe Electrical System Diagnosis Circuit Tester

  • Autor do post:
  • Post publicado:
  • Categoria do post:
  • Comentários do post:0 comentário

KZYEE KM50 Power Circuit Probe Kit, 7 Work Models , Automotive Circuit Tester with AC DC Current Resistance Circuit Tester Fuel Injector Testing (Digital Voltage Tester/Multimeter/Short Finder/Battery Tester) The KZYEE KM50 Power Scan kit is the most revolutionary circuit tester to date, which works off of 12-24 Volt sources, featuring DC Voltage, AC Voltage, Frequency, Duty Cycle, Fuel Injection Circuit Detection, Resistance, and Diode Especially, in AC Voltage, Frequency, Duty Cycle, and Fuel Inject Modes, users can long-press the mode button to switch between Waveform Display Mode and Digital Display Mode. The power scan is indeed the ultimate in power and affordability, allowing users to check circuitry in one single step. An absolute must for every technician who is looking for a fast and accurate solution to electrical systems diagnostic. Advance Features 1. Diagnose 12 ~24V automotive electrical systems swiftly and accurately. 2. Show battery voltage reading and help user determine circuit polarity immediately after connecting the KM50 clips to the vehicle battery. 3. Test DC Voltage, AC Voltage, Frequency, Duty Cycle, Fuel Injection Circuit, Resistance, and Diode. Especially, in AC Voltage, Frequency, Duty Cycle and Fuel Inject Modes, user can long press the mode button for 3 seconds to switch between Waveform Display Mode and Digital Display Mode. 4. Activate electrical components and test their functions without jumper leads – by depressing the rocker switch to conduct a positive or negative battery current to the tip so as to power up electrical components. 5. Test bad ground contacts instantly without performing voltage drop tests. 6. Help user to follow and locate short circuits without using external fuses. 7. Test continuity with the assistance of its auxiliary ground lead. 8. The tool is short-circuit protected. If it becomes overloaded, Its internal circuit breaker will trip to protect the instrument from overload. 9. When the circuit breaker is tripped, the tool will NOT be able to conduct battery current to the tip even when the rocker switch is pressed; however, all other functions of the tool are still active, which means you can still probe a circuit and observe the voltage reading. About this item 【Short Circuit Following and Locating Test Light】The circuit tester is suitable for diagnostic in all 12V to 24V DC vehicle electrical systems. It can check switches, relays and the on-off of diodes, fuses and circuits, which can help you reduce diagnostic time in automotive electrical systems. In most cases, short circuit or instant overload of component will lead to blown fuse or circuit breaker tripping.This probe tester can assist you tracing problem wires and locating breaking points. 【Polarity Identification & Continuity Testing & Jumper Lead Operation】This power circuit probe tester can help you quickly identify positive and negative polarity of electric cables and plugs of vehicles. When the probe tip contact to the positive electrode, the RED light on. When the probe tip contact to the negative electrode, the GREEN light on. It can also test for continuity and do the jumper lead operation with the assistance of its auxiliary ground lead. 【Activate and Test Components In/Out of Vehicle’s Electrical System&Poor Ground Contact Testing】Power circuit probe tester could activate components in and out of the vehicle’s electrical system, test and check the components if defective or not, or if rating current of component is higher than that of the circuit tester. For some components, the negative terminal is required to be well grounded to cope with the flow of large currents, this circuit tester is a good tool to test their grounding. 【20FT Long Cable&LED Light Prompt&Buzzer Warning&Highly Sensitive Probe&Clips with Strong Bite】The cable length of the circuit tracer is about 4m(13ft) which allows you access and test any electrical system easily. The LED indicator and buzzer warning can help you clear problems at a glance. Test light adopts advanced high sensitivity probe, which provides you quick and accurate detection. Its clips with strong bite force which not easy to fall off, providing you better experience. 【Quick Self-Test & Overload Protection】Before you test a circuit or component, the test light can perform a quick self-test to ensure your tool is in good condition. Equipped with overload protection, when the current exceeds 7A, the circuit tester will disconnect the current automatically and give you a buzzer prompt. You can test poor ground contacts directly. Note: This electrical tester can not be used for 110/220V systems, it is only used for DC 12-24V systems. Do not use on AC voltage. 【Automatic Reset Test Light】When the circuit breaker trip is detected, the power circuit probe tester will sound a prompt to remind you that there is a short circuit problem. Then it will automatically reset within 3 to 5 seconds(the prompt sound will automatically turn off), so you can retest or go to test other places. 【Easy Operation Circuit Tester】Unroll the leads. Clamp the red clip of the power circuit probe tester to the positive terminal of the vehicle's battery. Clamp the black clip to the negative terminal of the vehicle's battery. After a simple hook-up of the circuit tracer to the vehicle's battery, automotive technician can conduct a positive or negative battery current to the tip by rocking the power switch forward or backward. Features: 1.Performs every type of service including power injection, measurement, ground testing, polarity checks, continuity testing and components activation 2.Easy to read AVOmeter allows you to read voltage, current and resistance at the fingertip 3.With a flip of the power switch, you have an instant hot/ground lead for powering up electrical components like cooling fans, relays, etc. 4.Simultaneously uses the hot lead and the ground lead to activate components right in your hand 5.Instantly identifies positive, negative and open circuits 6.Tests for bad ground contacts instantly, allowing you to follow and locate shorts fast without wasting fuses 7.Instantly checks continuity of switches, relays and diodes 8.Circuit breaker protected 9.Built-in Flashlight enables you to work in the dark 10.Audio tone indicator allows for no-look menu scrolling once users are familiar with menu tone assignment 11.Long cable 6M/20ft (extendable) provides excellent accessibility to test along the vehicle 12. Powered by vehicle battery directly instead of applying extra battery inside the device. 13. Able to be used in dark places such as engine compartments by the equipped light-emitting diode. 14. The tool is the best electrical tester for reducing diagnostic time in all 8 DC- to 30 DC Voltage vehicle electrical systems. After a simple hook-up of the tool to the vehicle's battery, KM50 has more highlights than other circuit testers. Resistance Test: While the tool in this mode, contact the probe tip to a circuit, then the LCD display will read the resistance between the tip and auxiliary ground lead. Diode Test: In this mode, the probe tip contact the positive terminal of the diode, connect the auxiliary ground lead to the negative terminal of the diode, the screen will display the forward voltage drop, indicates the forward bias. If exchange the probe tip and auxiliary ground lead, the screen will not display the voltage, indicates the reverse bias. Signal Circuit Testing: Once you extract a DTC from the vehicle and realize that troubleshooting begins with some kind of sensor circuit, there is a quick test you can perform to verify the code. Testing your sensor is easy while using the tool. Testing Trailer Lights and Connections: While the tool in DC Voltage mode, clip the auxiliary ground lead to the trailer ground , probe the contacts at the jack and then apply voltage to the probe tip. This lets you check the function and orientation of the connector and trailer lights. Red/Green Polarity LED: The Red/Green Polarity LED lights up when the probe tip voltage matches the battery voltage within ±0.4 volts. It is added information that could be valuable to the technician. Auto Circuit Breaker: The tool is short-circuit protected. Its internal circuit breaker will trip if it becomes overload. The circuit breaker is a valuable test tool as well as a safety measure to protect the tool from overload. More Advance Features to Do Circuit Test Fuel Inject Mode: There are a variety of currently used techniques and tools that can test a fuel injector or injector circuitry; however it usually involves using multiple tools and tests to check every aspect of the injector circuit. Complete testing could take quite a bit of time. Fuel Inject Mode is specifically set up for quick and easy diagnosis of the fuel injection circuit. A quick connection to the circuit and the KM50 will display all the information needed to test the injectors. To reset the maximum and minimum values, press the mode button twice. If no valid injector pulse is detected in this mode, a bar icon will be displayed instead. Frequency and Duty Cycle Mode: The car's electronic control system communicates with various sensors via digital signals. When the car fails, you need to use the instrument to check whether the frequency of the signal or the duty cycle is abnormal. Press the Mode button to enter the menu, and press the Down button momentarily to place the cursor in the frequency mode, and press the Mode button momentarily to enter the frequency waveform display mode. Press the Mode button to enter the menu, and press the Down button momentarily to place the cursor in the Duty Cycle mode, and press the Mode button to switch to the waveform display. Buzzer and LED light are Switchable: When you measure the voltage DC, if the voltage is 0V, the green indicator light will be on and the buzzer will sound twice; if the voltage is above 5V, the red indicator light will be on and the buzzer will sound once. When the resistance value is less than 30Ω, the buzzer of the device sounds and the green indicator LED lights up.DC Voltage ModeDC mode is for testing DC (direct current) voltages. Voltage testing is as easy as contacting the probe tip to a circuit and reading the display.DC Mode is the mode that the KM50 can supply battery power or ground by pressing the rocker switch.AC Voltage ModeThe auxiliary ground wire is connected to one end of the circuit under test, and the probe contacts the other end of the test circuit. The LCD will display the max and mini voltage value, and display the signal waveform in real-time. You can adjust the sampling frequency by pressing the Up/Down Button.Resistance Testing ModeThe probe contacts one end of the measured resistance, and the auxiliary ground lead is connected to the other end of the measured resistance. The LCD will display the resistance between the tip and auxiliary ground lead. When resistance value is less than 30Ω, the instrument buzzer will alarm and the green LED will light. This function can be used as continuity test.Diode Testing ModeContact the probe tip to diode positive terminal, connect the auxiliary ground lead to the diode negative terminal, the screen will display the forward voltage drop, which indicates forward bias. If swapping the probe tip with auxiliary ground lead, the screen will not display voltage, which indicates reverse bias. It also displays the max and mini values during measurement. Resistance Test: While the tool in this mode, contact the probe tip to a circuit, then the LCD display will read the resistance between the tip and auxiliary ground lead. Diode Test: In this mode, the probe tip contact the positive terminal of the diode, connect the auxiliary ground lead to the negative terminal of the diode, the screen will display the forward voltage drop, indicates the forward bias. If exchange the probe tip and auxiliary ground lead, the screen will not display the voltage, indicates the reverse bias. Signal Circuit Testing: Once you extract a DTC from the vehicle and realize that troubleshooting begins with some kind of sensor circuit, there is a quick test you can perform to verify the code. Testing your sensor is easy while using the tool. Testing Trailer Lights and Connections: While the tool in DC Voltage mode, clip the auxiliary ground lead to the trailer ground , probe the contacts at the jack and then apply voltage to the probe tip. This lets you check the function and orientation of the connector and trailer lights. Red/Green Polarity LED: The Red/Green Polarity LED lights up when the probe tip voltage matches the battery voltage within ±0.4 volts. It is added information that could be valuable to the technician. Auto Circuit Breaker: The tool is short-circuit protected. Its internal circuit breaker will trip if it becomes overload. The circuit breaker is a valuable test tool as well as a safety measure to protect the tool from overload.TIPS: 1. KM50 is ONLY for 12-24V vehicle battery electrical systems, and should NOT be used to test 110/220V household appliances or it will be damaged. 2. The LED and LCD draw no more than 100 milliamps of current. So if you use this device as a test light or multimeter, it is safe for computers and airbags. 3. When turning on components, you can extend the life of rocker switch in the tool if you first press the switch, and then apply the tip to the component. The arc will then occur at the tip and not at the metal contacts of the rocker switch. Product SpecificationsSupply Voltage: 8V DC ~ 30V DC；Frequency: 0Hz ~ 1Mhz DC/ AC Voltage Test: -110V ~ 110VDuty Cycle: 0.0~100.0%；Rating Current: 1A~8 A Fuel Injection:Voltage: 0~180V, Time: 0~25msDisplay TFT color display (160x128 dpi )Operating Temperature -10 ~ +60°C ( 14 ~ 140°F)Storage Temperature -20 ~ +70°C (-4 ~ 158°F )Dimensions (L*W*H) 200mm*52mm*39mmNet Weight :1.25Kg(2) Electrical SpecificationsSupply Voltage 8V DC ~ 30V DCDC/ AC Voltage Test -110V ~ 110VFrequency 0Hz ~ 1MhzDuty Cycle 0.0~100.0%Fuel Injection Voltage: 0~180V, Time: 0~25msResistance 0~1MΩDiode Germanium diode, silicon diodeRating Current 1A~8 A Instrument Trip Time:8 Amps: Hold > 1 hour.12 Amps: current: trip in one hour.16 Amps: current: trip in 3-30 seconds.24 Amps: current: trip in 0.5-4.0 seconds Product Appearance Introduce 1) Probe Tip - Contacts the circuit orcomponent to be tested. 2) LED Lights - Illuminates dark workareas or work areas at night. 3) LCD Display - Indicates test results,test data and waveforms. 4) Red/ Green Polarity Indicator -Identifies positive, negative or open circuits. The RED Indicator lights when the Probe Tip is contacting a positive circuit. The GREEN Indicator lights when the probe tip is contacting a negative or negative voltage circuit. When the resistance is being measured, the green indicator light is on when the resistance is less than 30Ω. 5) Function Button: Switching Light ON &OFF/Up Button - short press is the up button, long press is to turn the light on/off; Mode Button - for selecting test mode; S ilent/Down Button - short press is the down button, long press is to turn on/off the buzzer. 6) Rocker Switch - Allows you to conduct a positive or negative battery current to the tip for activating and testing the function of electrical components. 7) Auxiliary Ground Lead - Assists test as a ground lead. 8) Red/Black Alligator Clips - Clip the red alligator clip to the battery positive pole; Clip the black alligator clip to the battery negative pole. PaymentDelivery detailsTerms of salesAbout usContact usPayment We accept all common forms of payment such as Credit cards、Debit card、Google Pay ect. Please contact us if you need to use another method to pay. Payment should be made within 7 days after bidding ends. Otherwise a Unpaid Item case will be opened to you. We are not responsible for buyers’ local taxes. Please include your special requests in eBay note if there is any.Delivery detailsOrder will be shipped within 1 business day after payment confirmed.We have warehouse in USA, From our US warehouse via UPS or USPS shipping. Delivery time varies from 2 to 5 business days.We will ship according to your eBay address. Please make sure it is correct and include phone number for delivery.If you do not receive your order in the estimated time, please contact us, we would do our best to serve you solve the problem. Please include your special requests in eBay note if there is any.Terms of salesReturn PolicyPlease return the item within 60 daysafter receiving if you are not happy with your purchasing.All returns are expected to be in original conditions, please email us first for return address and instructions. We are authorize distributor, our all items are 100% original and Our devices have warranty, 5 Year free repair for the devices. Please contact us firstly when you need warranty service. In case an item arrives faulty, please contact us as soon as possible and keep it unused. We will instruct you on how to return and get refund or replacement. If the item has been used, we have the right to decline your claim. Items should be returned on buyers' cost for repair or replacement.About usWho We Are? We are specialized dealer of On-Board Car Diagnostic tools and automotive electronics for more than 10 years. We are authorized first class distributor of Launch, Foxwell, Autek, Ancel, Innova, Autophix, Thinkcar, Kzyee brands, and more brands will be show in our store in near future. What Do We Have? We have office and warehouse in US to ensure fast shipment and after-sale service. We have more than 100 employees devoting to customer satisfaction. Contact us 1:If youhave any problem about the goods, please contact us before leaving Neutral/Negative feedback.We promise to help you solve it asap, and make you feel satisfactory absolutely. 2: our business time:M-F: 9:30AM - 18:00PM BST (Beijing Standard Time) 3:Please leave us Positive Feedback and 5-stars★★★★★after you received our package you are satisfied with it. as you know, every seller works hard for the positive feedback. We will do the same as soon as we can too.On Oct 11, 2023 at 14:06:36 PDT, seller added the following information:

Continue lendoKZYEE KM50 Car PowerScan 12&24V Probe Electrical System Diagnosis Circuit Tester

THINKDIAG All Brand Free Bi-directional OBD2 Scanner Diagnostic Tool Code Reader

  • Autor do post:
  • Post publicado:
  • Categoria do post:
  • Comentários do post:0 comentário

2022 THINKDIAG X431 PRO Bi-directional OBD2 Scanner Diagnostic Tool Code ReaderThinkdiag OBD2 Scanner Bluetooth, All System Bidirectional scan Tool OE Level Diagnostic Tools with ECU Coding,15+ Service Functions All Software 1 Year Free fits for iPhone & Android 2022 Global Version,No IP Limited,Same function as MK808If you need thinkdiag old version,please contact me! ThinkDiag, as an OBD2 diagnostic adapter that works with iOS or Android devices paired with exclusive “ThinkDiag App”, gets Active Test, All System Diagnoses, along with 15 maintenance services, and other effective features in creating easy work to help you diagnose cost-effectivelyNOTE: This version of THINKDIAG is free for all software, no need to pay separately after purchase, all the software that needs to be downloaded in it are free. And is to provide one year of free upgrades.NOTE: Please download THINKDIAG APP (DZ, DIAGEASY and other apps are not available), When you register with the THINKDIAG APP, all models and features are free to use. If you still need to pay for the download, please contact me, I will help you open the free access to all functions. 【What IS THINKDIAG】THINKDIAG is an automobile diagnostic tool with professional-grade functions. In the past, mechanics and car tuners had to use bulky diagnostic tools with large screens and connector cables, or laptops plugging into the OBD II port. THINKDIAG changes that. Plug the THINKDIAG dongle into your car, connect it to your smartphone via Bluetooth, and your smartphone becomes a professional diagnostic tool. THINKDIAG is small to be in your pocket, but it is smart and powerful enough to enjoy as much as 15 maintenance functions, advanced ECU coding, accurate Bidirectional functions, enhanced tests for the full electronic control system, full OBD II and EOBD functions.【WHY SHOULD YOU CHOOSE THINKDIAG】 THINKDIAG is much more cost-effective when compared with its counterparts like BlueDriver LSB2, MX+, LX Bluetooth. It has its unique feature to enjoy a super stable Bluetooth connection with professionals millions times researching and testing. You are able to watch 4 realtime data stream, which is a single 1 is allowed to be seen on other OBD2 scanners; You are able to have professional coding function (Like LAUNCH X431 V+, MS906), actuation test, up to 15 maintenance functions, OBD2 all system diagnosis, auto on function, remote diagnose, online diagnostic report, community interaction. Besides, special functions of 115 car brands that are specific to each car model or series, so you don't need multiple expensive special equipments.【WHAT YOU CAN GET】 = Have Your Own Mechanic = If you are a professional technician repair shops, ThinkDiag fully meets your daily needs, Outbound business, road assistance. This Bluetooth scanner functions the same as thousands of dollars valued diagnostic tools, but in a much lower, more portable. Get fast vehicle diagnostic results with less cost and sweat. If you are tired of expensive repairs, and have the hands-on ability, ThinkDiag breaks down problems into simple and understandable terms, being your own car doctor, right on your smartphone. A No Brainer, the Time is Worth Way More it Costs【Full-System Diagnoses】THINKDIAG enables you to scan full control units for a number of cars such as Engine, ABS, SAS, Transmission, Fuel system, Emission system, Body, and so on. Therefore, there is no need to buy other tools for diagnosing systems, saving you much time and money for the long term.This option allows you to detect whether the car full system parameters are normal or not. It mainly including:Engines/Auto Transmission/Airbags/Immobilizer/Key Coding/ABS/Cruise Control/Instruments/ Self Leveling Suspension systems/Seats/Doors/Gateway/Steering Angle/Air Suspension/Body Systems/Electronic Power Steering & Motor Assisted/Power Steering/Tyre Pressure/Rain Sensors/4WD System/Stabilizer/Intelligent Parking Assist/Door Motors/Audio Systems/Air Conditioning/Tiptronic/Anti Theft/Soft Top/Headlamp Leveling/Central Locking/Automatic Clutch/ DPF Reset/Electric Windows/Plip Programming/Heated Rear Window/Xenon Headlights/Wash Wipe/Fuel Burning Heater/Transfer Box/Seat Memory/Oil Life Service Reset/Sliding Doors/Electronic Throttle/Navigation System/Rollover Sensor/Cruise Control/ Multi Function Steering Wheel/Aux Heating/Electronic Parking Brake/Clutch Electronics etc.( Great for car repair shops and mechanics to improve business)【Basics+High Diagnostic Functions】THINKDIAG enables you to CODING, Actuation Test,. Matching, Adaptation, Initialization, Service Functions. And it can also perform read/clear DTCs, view live data, Read the vehicle ECU information. 1. ECU Coding:The Coding function is used to re-flash the vehicle control modules, it allows you to reprogram adaptive data for certain components after making repairs or replacements, providing ways for the issues of Drivability, Fuel Efficiency, Power Loss, Fault Codes, Durability of Mechanical Parts. FORD, GM, BUICK, BENZ, AUDI, VW, PORSCHE, KIA, HYUNDAI, etc. (coding highly configured hide function) Notice: ECU CODING and KEY CODING are not applicable to all models, please send your model and year model, AND I will help you determine whether they are suitable!!! 2. Bi-directional Control(Actuation Test):Requests a module to perform a specific test and function. (Turn on and off actuators to determine whether there are problems with sensors and actuators). This function can be used in ENGINE SYSTEM /STEERING ANGLE SYSTEM / DASHBOARD SYSTEM / EMISSION SYSTEM... etc.. (Depends on the specific car models, not for all cars)3. Matching: This function matches and synchronizes the components with each module after you replace the module, such as: Gearbox Matching / Air Suspension Matching / Seat Matching / Head light Fitting / Door and Window Initialization Study / Sunroof Initialization / Injector Calibration / Multimedia Video Reset / Cluster Reset / Immobilizer Service / Tire Change Reset... etc. (Depends on specific car models, not for all cars) 4. 16 Service Functions:1.Oil Reset ServiceThe lightening of the car maintenance light indicates that the vehicle needs maintenance.Reset themileage or driving time to zero after the maintenance, so the maintenance light will go out and the systemwill start a new maintenance cycle.2.Steering Angle CalibrationTo reset the steering angle, first find the relative zero point position for the car to drive in straight line.Taking this position as reference, the ECU can calculate the accurate angle for left and right steering.After replacing the steering angle position sensor, replacing steering mechanical parts (such as steeringgearbox, steering column, end tie rod, steering knuckle), performing four-wheel alignment, or recoveringcar body, you must reset the steering angle.3.Electronic Parking Brake Resetlf the brake pad wears the brake pad sense line, the brake pad sense line sends a signal sense line to theon-board computer to replace the brake pad.After replacing the brake pad, you must reset the brake pad.Otherwise, the car alarms.4.Battery Register & Battery MaintenanceThis function enables you to perform a resetting operation on the monitoring unit of vehicle battery, inwhich the original low battery fault information will be cleared and battery matching will be done.5.ABS BleedingWhen the ABS contains air, the ABS bleeding function must be performed to bleed the brake system torestore ABS brake sensitivity. lf the ABS computer,ABS pump, brake master cylinder, brake cylinder, brakeline, or brake fluid is replaced, the ABS bleeding function must be performed to bleed the ABS.6.Electronic Throttle Position Reset & LearnElec. Throttle Adaption is to utilize the car decoder to initialize the throttle actuator so that the learningvalue of the ECU returns to the initial state.By doing these, the movement of the throttle (or idle motor)can be more accurately controlled, thus adjust the intake volume.7.Diesel Particulate Filter (DPF) RegenerationDPF regeneration is used to clear PM (Particulate Matter) from the DPF filter through continuouscombustion oxidation mode (such as high temperature heating combustion, fuel additive or catalyst reducePM ignition combustion) to stabilize the filter performance.8.Tire Pressure Monitor System ResetAfter the tire pressure MIL turns on and maintenance is performed, the tire pressure resetting functionmust be performed to reset tire pressure and turn off the tire pressure MIL.Tire pressure resetting mustbe performed after maintenance is performed in the following cases: tire pressure is too low, tire leaks, tirepressure monitoring device is replaced or installed, tire is replaced, tire pressure sensor is damaged,andtire is replaced for the car with tire pressure monitoring function.9.Gear LearningThe crankshaft position sensor learns crankshaft gear machining tolerance and saves to the computerto more accurately diagnose engine misfires. lf gear learning is not performed for a car equipped withDelphi engine, the MlL turns on after the engine is started.The diagnostic device detects the DTC P1336'gear not learned'. In this case, you must use the diagnostic device to perform gear learning for the car.After gear learning is successful, the MIL turns off. After the engine ECU, crankshaft position sensor, orcrankshaft flywheel is replaced, or the DTC 'gear not learned" is present, gear learning must be performed.10.Anti-theft ( IMMO ) MatchingTo prevent the car being used by unauthorized keys, the anti-theft key matching function must beperformed so that the immobilizer control system on the car identifies and authorizes remote control keysto normally use the car. When the ignition switch key, ignition switch, combined instrument panel,ECu,BCM, or remote control battery is replaced, anti-theft key matching must be performed.11.Injector matching MaEETWrite injector actual code or rewrite code in the ECU to the injector code of the corresponding cylinder soas to more accurately control or correct cylinder injection quantity. After the ECU or injector is replaced,injector code of each cylinder must be confirmed or re-coded so that the cylinder can better identifyinjectors to accurately control fuel injection.12.Air Suspension ResetThis function can adjust the height of the body. When replacing the body height sensor in the airsuspension system, or control module or when the vehicle level is incorrect, you need to perform thisfunction to adjust the body height sensor for level calibration.13. Gearbox /Transimission ResetThis function can complete the gearbox self-learning to improve gear shifting quality. When the gearbox isdisassembled or repaired (after some of the car battery is powered off), it will lead to shift delay or impactproblem. In this case, this function needs to be done so that the gearbox can automatically compensateaccording to the driving conditions so as to achieve more comfortable and better shift quality.14.Sunroof RESETThis function can set the sunroof lock off, closed when it rains,sliding / tilting sunroof memory function,temperature threshold outside the car etc.15.AFS Reset (EGR)This feature is used to initialize the adaptive headlamp system.According to the ambient light intensity, theadaptive headlamp system may decide whether to automatically turn on the headlamps, and timely adjustthe headlamp lighting angle while monitoring the vehicle speed and body posture.16.EGR ResetThis function is used to learn the EGR (Exhaust Gas Recirculation) valve after it is cleaned or replaced.Note : These special function NOT for all car models, if you are confused, Please send your car brand, model and release year to seller to check it for you .【Covering 99.99% Vehicles on the World & 9 Language】THINKDIAG works on ECU of vehicle models covering American, Asian, European, Malaysia, India car brands up to 150 car brands, 10000 car models.9Language: English,Polish, German, Russian, French, Portuguese, Spanish,Italian, Japanese are available to choose,so you can freely use your native language software as you like.If you are not sure whether your car supports it, please send me VIN number or model year and I will help you to confirm.【One Key Update &1(ONE) Years Free Update】THINKDIAG comes with 1 years free software updates which are updated frequently to improve its capability and coverage continuously. If you do not renew after one year, you will still be able to use OBDII diagnostics, but advanced diagnostics will be prohibited.Please contact me to renew your subscription after one year, preferential price!TOP OBD Exclusive Benefits: a one-year full software subscription only costs 69 US dollars! ! Two-year subscription for $129! ! ! ($129 per year in THINKDIAG APP)【THINKDIAG Other Highlights】 >1--One-Click Generate Health Report&Print This diagnostic tool can automatically generate a diagnostic report when diagnostic work is successfully finished. These can be emailed to the office or directly to the customer. The diagnostic report can better show your professionalism and help you improve your business >2--Data Stream record/playback and Live Data Graphing IN 1 Screen Data Stream is so important is to enable the vehicle technician to examine the relationships between the various sensors, actuators and calculated values. This is critical for intermittent fault finding and for vehicle problems. X431 V did a good job. Live data graphs quantity at the same time - up to 4 on the screen >4--View History Once a vehicle diagnosis is performed, X431 V will record the every detail of the diagnostic process. The History function provides quick access to the tested vehicles and users can resume from the last operation, without the necessity of starting from scratch >5--AutoVIN: No need to get the VIN from the plate that's near the windshield and manually input the code. LAUNCH X431 V can automatically read the vehicle information after a successful data link connection. >6--Regular Software Updates: We will continue to update the diagnostic software, and you can directly download the latest version of the software via WIFI. Model model, special function, ECU CODING, Actuation Test,. Matching, Adaptation, Initialization,etc. Don’t worry if your device can’t keep up with the time 【Specifications】Working Voltage: 9V~18VWorking Current: ≤130mAWorking Environment: 14℉~122℉ (-10℃~50℃)Storage Environment: -4℉~140℉ (-20℃~60℃)Product Dimensions: 78*55*28 mm (3.07*2.17*1.10 inch)Package Dimensions: 115*75*35 mm (4.53*2.95*1.38 inch)Weight: 125g (4.41 oz)【Package include】1*ThinkDiag1*User Manual PaymentDelivery detailsTerms of salesAbout usContact usPaymentWe accept PayPal payment.Please contact us if you need to use another method to pay.Payment should be made within 7 days after bidding ends.Otherwise a Unpaid Item case will be opened to you.Delivery detailsShippingOrder will be shipped within 3business day after payment confirmed.We have warehouse in USA，UK，HongKong，Australia，Russian，Germany and China warehouse.From our US/UK/RU/DE/AU warehouse via UPS or USPS shippingDelivery time varies from 2 to 10 business days.From our Hong Kong warehouse via DHL or FedEx GroundDelivery time varies from 3 to 5 business days.From our China warehouseFor US buyers, we use e-Packet (Delivery time is 5-12 business days) or express delivery(Delivery time is 3-7 business days) .For other countries' buyers, we use China Post or Hong Kong Post(Delivery time varies from 10 to 25 business days)or Express delivery(Delivery time is 3-7 business days).We will ship according to your PayPal address.Please make sure it is correct and include phone number for delivery.If you do not receive your order in the estimated time, please contact us, we would do our best to serve you solve the problem.Please include your special requests in eBay note if there is any.Terms of salesWe are authorize distributor, our all items are 100% original and Our devices have warranty, 12 months free repair for the devices. 3 months for the accessories.Please contact us firstly when you need warranty service.In case an item arrives faulty, please contact us in 7 days and keep it unused.We will instruct you on how to return and get refund or replacement.If after 7 days, or the item has been used, we have the right to decline your claim.Items should be returned on buyers' cost for repair or replacement.About usWho We Are?Shenzhen Kingbolen Electrics Technology Co., Ltd., founded in 2005, is a comprehensive enterprise dedicated to the research, development, manufacture and international sale of automotive diagnostic tools.We are specialized dealer of On-Board Diagnostic tools and automotive electronics over 10 years.We are authorized first class distributor of Launch,THINKCAR ,EDIAG, OBDSTAR,etc., and more brands will Join us in near future.Terms of tax:We are not responsible for buyers local taxes, please consult your local Customs for tax details. Contact usOur customer-oriented service strives for positive feedbacks with all 5 star selling ratings. Please feel free to contact us via eBay message once you have any question before you giving us negative feedback or open case. We will reply in 24 business hours. Business time: GMT8 (8:30-18:00) from Monday to Friday.

Continue lendoTHINKDIAG All Brand Free Bi-directional OBD2 Scanner Diagnostic Tool Code Reader

Super EL-50448 TPMS Reset Tool Tire Pressure Monitor Sensor Relearn For Ford GM

  • Autor do post:
  • Post publicado:
  • Categoria do post:
  • Comentários do post:0 comentário

Super EL-50448 TPMS Reset Tool Tire Pressure Monitor Sensor Relearn For Ford GM TPMS tool is a tire relearn tool to work for both GM and Ford series vehicle Tire Pressure Monitoring system sensor. This is an essential tool of replacement tire pressure sensor, tire pressure alarm remove or exchange tires for GM / Chevy / Buick / GMC / Opel / Cadillac / Ford / Lincoln / Mercury etc. Applicable Models(FORD+GM) 2006-2020 compatible with almost all GM Series vehilces: Buick, Cadillac, Chevy, GMC,Opel 2006-2010 compatible with Saab, Pontiac,Hummer, Saturn 2007-2020 compatible with F-150,Edge; 2008-2015 F-250 F-350 F-450 F-550 Super Duty 2006-2020 compatible with Mustang; 2006-2015 Escape; Explorer 2008-2020 compatible with Expedition,Flex,Taurus,E-150 E-250 E-350 E-450 Econoline Vans,Fiesta,Focus,Fusion; Lincoln MKZ, MKS,Navigator 2008-2011 compatible with Crown Victoria,Lincoln Town Car 2011-2020 compatible with Transit Connect 2006-2011 compatible with Ranger;Mercury Mariner,Grand Marquis,Milan 2007-2020 compatible with Lincoln MKX,MKT;2007-2008 Lincoln Mark LT 2006-2010 compatible with Mercury Mountaineer,Monterey If you do not find your model, please send the year and model to me, I will help you confirm (Equipped with 315/433 MHz, It won't work if you've purchased aftermarket sensors with wrong frequency.) KINGBOLEN EL-50448 TPMS Relearn tool is an useful Activation Tool for G*M series Vehicles.It can quickly reset tire sensors after you do tire rotation or change a new tire ,very easy to use and convenient,saving you trips to your dealer.It is suitable for GM Vehicles(for Chevy / for Buick / for GMC / for Opel /for Cadillac etc) Ford Vehicles(for F-150 / F-250 / Mustang / Explorer / Lincoln / Mercury etc)that equipped with 315/433 MHz tire pressure monitor system Sensors. When do U need relearn tool? 1.New TPMS sensors installed, letting air out or adding air in to the tire couldn’t make the system recognize new sensors. 2.Do tire rotation, didn’t have a quick and easy way to let ECU relearn new tire information. 3.When tire pressure indicator light ON, after the maintenance performed, the tire pressure needs to be reset to turn off the TPMS light. 4.Low tire pressure or leakage /replacement or installation of tire pressure monitoring equipment / tire replacement, sensor damage, etc. After those problems solved, TPMS needs to be reset. 5.Exchanging the winter tires or Summer tires. How to set your car in TPMS relearn mode? For GM vehicle Set the parking brake. Keep the ignition position to ON (with the engine off). Press the Key Fob (lock and unlock) at the same time for 5 seconds. It will cause the horn to beep twice indicating that relearn mode is on. For Ford vehicle Ignition switch to OFF, press and release the brake pedal. Turn ignition switch from OFF position to RUN position 3 times and end at RUN position. Depress and release the brake pedal and Ignition to OFF position. Ignition goes from OFF position to RUN position 3 times and ends at RUN position. How to use EL-50448 relearn tool? Set the car in TPMS learning mode. (car horns twice) Starting relearn process from left front tire, point antenna on correct position. Press & release power button. Once the speaker chirped, move to the next tire. Follow this order to rest TPMS sensors: Front left, front right, rear right, rear left. After all sensors reseted, the car horns twice means TPMS re-learn finished. Friendly Tips 9V battery should be in good condition : NEW & fully charged.(Kindly Note: There is no 9V battery inside package, you need to prepare that yourself.) Please make sure antenna fit in CORRECT position. Do tire reset outside instead of in the garage. Position of tires is also important, Front tires have to be straight. Sensors should be original OEM sensors which well programmed.WARRANTY POLICYShippingPaymentAbout usContact usWARRANTY POLICYWe offer more than 60 day warranty for all items. Please check that the item is correct and in good condition before installation. Please contact our customer service support team through ebay message if the items have any problems. When exchanging or returning, all products MUST BE IN ORIGINAL PACKAGING. Please note no exchanges will be accepted on products that have been improperly damaged, used or modified.ShippingWe ship package directly from our USA California warehouse 2-5 Business Days(EXCEPT WEEKENDS)by UPS/Fedex/USPS.Tracking number will be provided.Buyers are responsible for applicable tax or duty that might be charged by customs or government.If your address is in HI, AK, VI, GU or PR. Plz contact us for the extra shipping fee.PaymentBuyers may pay for your items using payment methods such as the following: Certain credit or debit cards (VISA, MasterCard, American Express, and Discover),PayPal,Google Pay,Apple Pay,Direct debit, or eBay coupons, gift cards, etc. (if applicable).Payment must be made within 5 days after you bid. Or the transaction will be cancelled. About usWe pride ourselves in the quality of our parts, integrity, and customer service. Our company has been around for over 30 years. We are proud to operate our own on-site, 100,000 square foot warehouse where thousands of parts ship weekly.Contact usNote: If u have any problems, complaint ,advise ,please give us eBay message First Before Any Feedback. We will reply your message and solve your problem during working time ASAP.

Continue lendoSuper EL-50448 TPMS Reset Tool Tire Pressure Monitor Sensor Relearn For Ford GM

EL-50448 TPMS Reset Tool Relearn Tool Auto Tire Pressure Sensor for GM Vehicles

  • Autor do post:
  • Post publicado:
  • Categoria do post:
  • Comentários do post:0 comentário

Store category Sign Up Now ! You may also like TPMS Auto Tire Pressure Monitor Sensor Reset Tool OEC-T5 EL-50448 For GM Vehicle Product Description Dear Customer If have any question, please don't leave negative feedback or open any return request,please contact us first, we will do our best help you Specification: Most of G.M vehicles equipped with a 315 or 433 MHz (TPMS) Tire Pressure Monitoring system, a "Sensor Re-Learn Procedure" must be performed after tire rotations, Remote Control Door Lock Receiver Module replacement or Tire Pressure Sensor replacement. This re-learn procedure can be performed by using EL-50448 special tire pressure tool.EL-50448works on 2014 G.M models too. Description of the item:Compact design makes it lightweight and portable, easy to carry.Checking the pressure condition of the tyre in the real time.The tire pressure sensor on models in & after 2012 can be read, only with some specified diagnostic tools.With diagnostic sensing function.It is universal, suitable for most car. How to use: The tire pressure sensor on models in and after 2012 can be read, only with some specified diagnostic tools. Before tire pressure monitoring system works normally properly, the body control module will record ID information of each position in the tire pressure sensor; and use the following methods to read the tire pressure sensor. After replacing a tire or wheel speed sensor. Please refer to the specific methods as follows:Step 1 - Enter leaning modeSet the gearshift lever to "P"Put the ignition switch to "ON"Enter the interface of tire pressure display by DICDIC shows "Press Set / Ctrl to re-learn"Press "Set / Ctrl"The turn signal is lighted for 3 seconds and the horn beep sound twice to enter the learning modeStep 2 - Read tire pressure sensor informationStart from the front-left wheelMake the J-46079 or Diagnostic Tool EL-50448 antenna up against the valve core position & close to the rim of the tire sidewallEl-50448 tire pressure tool starts by the start switchSuccessful to read the tire pressure sensor information when the horn bleeps onceStep 3 - Same method to read other tire pressure informationFollow the instruction above to read tire pussure of the front-right, rear-right, rear-left wheelsTurn signals is lighted for 3 seconds and the horn bleeps twice when the learning is complete Package Included: 1 x EL-50448 tool Note: The package does not include the charger and battery, please buy them by yourself. Fit For These Vehicle :2010 9-5 2010 Acadia, Enclave, OUTLOOK, Traverse (VIN R/V) 2010 Allure, LaCrosse (VIN G) 2010 Antara, Captiva, Terrain, Winstorm 2010 Avalanche, Escalade, Suburban, Tahoe, Yukon (VIN C/K) 2010 Aveo, G3, Barina (VIN S/T) 2010 Buick Excelle 2010 Buick Regal (China) 2010 Camaro (VIN F) 2010 Canyon, Colorado (VIN S/T) 2010 Cobalt, G5 (VIN A) 2010 Corvette (VIN Y) 2010 Cruze (China) 2010 Cruze 2010 CTS (VIN D) 2010 Daewoo Lacetti 2010 DTS (VIN K) 2010 Equinox, Terrain (VIN L) 2010 Express, Savana (VIN G/H) 2010 G6 (VIN Z) 2010 H3/H3T (VIN N) 2010 HHR (VIN A) 2010 Impala (VIN W) 2010 Insignia 2010 LaCrosse (China) 2010 Lucerne (VIN H) 2010 Malibu (VIN Z) 2010 Opel/Vauxhall Astra 2010 Sierra, Silverado (VIN C/K) 2010 SKY, Solstice (VIN M) 2010 SRX (VIN N) 2010 STS (VIN D) 2010 VE/WM - Sedan, Sportwagon, Ute, Lumina, Caprice, HSV 2010 VUE (VIN Z), Captiva Sport 2011 Acadia, Enclave, Traverse (VIN R/V) 2011 Alpheon 2011 Antara, Captiva 2011 Astra 2011 Avalanche, Escalade, Suburban, Tahoe, Yukon (VIN C/K) 2011 Aveo, Barina (VIN S/T) 2011 Buick Excelle 2011 Buick Regal (China) 2011 Camaro (VIN F) 2011 Canyon, Colorado (VIN S/T) 2011 Caprice PPV 2011 Captiva Sport 2011 Corvette (VIN Y) 2011 Cruze 2011 CTS (VIN D) 2011 DTS (VIN K) 2011 Equinox, Terrain (VIN L) 2011 Express, Savana (VIN G/H) 2011 HHR (VIN A) 2011 Impala (VIN W) 2011 Insignia 2011 LaCrosse (China) 2011 Lucerne (VIN H) 2011 Malibu (VIN Z) 2011 Orlando 2011 Regal (VIN G) 2011 Sierra, Silverado (VIN C/K) 2011 SRX (VIN N) 2011 STS (VIN D) 2011 VE/WM - Sedan, Ute, Sportwagon, Caprice, Lumina, Omega, VXR8 2011 Volt 2012 Acadia, Enclave, Traverse (VIN R/V) 2012 Alpheon (2706)2012 Ampera, Volt (VIN R) (Europe) 2012 Antara, Captiva 2012 Astra-J (2857)2012 Avalanche, Escalade, Suburban, Tahoe, Yukon (VIN C/K) 2012 Aveo Classic, Barina Classic (VIN T) 2012 Aveo, Sonic (2777)2012 Barina (2774)2012 Buick Excelle (2861)2012 Camaro (VIN F) 2012 Canyon, Colorado (VIN S/T) 2012 Caprice PPV 2012 Captiva Sport 2012 Chevrolet Cobalt (2809)2012 Colorado (Other IO), S10 (South America) 2012 Corvette (VIN Y) 2012 Cruze (2863)2012 CTS (VIN D) 2012 Equinox, Terrain (VIN L) 2012 Express, Savana (VIN G/H) 2012 Impala (VIN W) 2012 Insignia (2707)2012 LaCrosse (China) (2710)2012 LaCrosse (VIN G) (2709)2012 Malibu (VIN Z) 2012 Opel Combo-D 2012 Optra, Viva (VIN J) 2012 Orlando (2859)2012 Regal (China) (2711)2012 Regal (VIN G) (2708)2012 Sierra, Silverado (VIN C/K) 2012 Sonic (US/Canada) (2775)2012 SRX (VIN N) 2012 VE/WM - Sedan, Ute, Sportwagon, Caprice, Lumina, VXR8 2012 Verano (US/Canada) (2816)2012 Volt (VIN R) 2012 Zafira-C (2860)2013 Acadia, Enclave, Traverse (VIN R/V) (3206)2013 Alpheon (3094)2013 Ampera, Volt (VIN R) (Europe) (3211)2013 Antara, Captiva (5376555)2013 Astra-J Convertible/Coupe (5376567)2013 Astra-J (5376577)2013 ATS (VIN A) (3086)2013 Avalanche, Escalade, Suburban, Tahoe, Yukon (VIN C/K) (3088)2013 Aveo, Sonic (Africa, Middle East, AP, South America, CKD, Mexico) (5376711)2013 Aveo, Sonic (Europe) (5376704)2013 Barina (5376837)2013 Camaro (VIN F) (3106)2013 Caprice PPV (3105)2013 Captiva Sport (3101)2013 Cobalt (3107)2013 Colorado, Colorado 7, S10, Trailblazer (5392270)2013 Combo-D 2013 Corvette (VIN Y) (3104)2013 Cruze (Global) (5377099)2013 CTS (VIN D) (3085)2013 Encore (China) (5377162)2013 Encore, Trax (North America) (5377181)2013 Equinox, Terrain (VIN L) (3100)2013 Excelle (5377155)2013 Express, Savana (VIN G/H) (3103)2013 Impala (VIN W) (3102)2013 Insignia (3098)2013 LaCrosse (China) (3095)2013 LaCrosse (VIN G) (North America) (3090)2013 Malibu (China) (3096)2013 Malibu (Europe, Other IO and South America) (2713)2013 Malibu (North America) (3093)2013 Mokka, Trax, Tracker (Europe) (5377179)2013 Onix (3166)2013 Orlando (Global) (5377530)2013 Regal (China) (3099)2013 Regal (VIN G) (North America) (3089)2013 Sierra, Silverado (VIN C/K) (3087)2013 Sonic (US/Canada) (5377994)2013 Spark (US/Canada), Barina Spark (Automatic Transmission) (5421555)2013 Spin 2013 SRX (VIN N) (3201)2013 Trax, Tracker (Africa, Australia, Middle East, South America) (5377156)2013 VE/WM Ute, Caprice, Lumina 2013 Verano (US/Canada) (5377996)2013 Volt (VIN R) (North America, Holden) (3210)2013 XTS (China) (3092)2013 XTS (North America) (3091)2013 Zafira-Tourer

Continue lendoEL-50448 TPMS Reset Tool Relearn Tool Auto Tire Pressure Sensor for GM Vehicles

EL-50448 OEC-T5 Auto Tire Pressure Monitor Sensor Activation Tool TPMS For GM F

  • Autor do post:
  • Post publicado:
  • Categoria do post:
  • Comentários do post:0 comentário

Most of G.M vehicles equipped with a 315 or 433 MHz (TPMS) Tire Pressure Monitoring system, a "Sensor Re-Learn Procedure" must be performed after tire rotations, Remote Control Door Lock Receiver Module replacement or Tire Pressure Sensor replacement. This re-learn procedure can be performed by using EL-50448 special tire pressure tool.EL-50448works on 2014 G.M models too.EL-50448 OEC-T5 Auto Tire Pressure Monitor Sensor Activation Tool TPMS For GM FVehicle List 2010 9-5 2010 Acadia, Enclave, OUTLOOK, Traverse (VIN R/V) 2010 Allure, LaCrosse (VIN G) 2010 Antara, Captiva, Terrain, Winstorm 2010 Avalanche, Escalade, Suburban, Tahoe, Yukon (VIN C/K) 2010 Aveo, G3, Barina (VIN S/T) 2010 Buick Excelle 2010 Buick Regal (China) 2010 Camaro (VIN F) 2010 Canyon, Colorado (VIN S/T) 2010 Cobalt, G5 (VIN A) 2010 Corvette (VIN Y) 2010 Cruze (China) 2010 Cruze 2010 CTS (VIN D) 2010 Daewoo Lacetti 2010 DTS (VIN K) 2010 Equinox, Terrain (VIN L) 2010 Express, Savana (VIN G/H) 2010 G6 (VIN Z) 2010 H3/H3T (VIN N) 2010 HHR (VIN A) 2010 Impala (VIN W) 2010 Insignia 2010 LaCrosse (China) 2010 Lucerne (VIN H) 2010 Malibu (VIN Z) 2010 Opel/Vauxhall Astra 2010 Sierra, Silverado (VIN C/K) 2010 SKY, Solstice (VIN M) 2010 SRX (VIN N) 2010 STS (VIN D) 2010 VE/WM - Sedan, Sportwagon, Ute, Lumina, Caprice, HSV 2010 VUE (VIN Z), Captiva Sport 2011 Acadia, Enclave, Traverse (VIN R/V) 2011 Alpheon 2011 Antara, Captiva 2011 Astra 2011 Avalanche, Escalade, Suburban, Tahoe, Yukon (VIN C/K) 2011 Aveo, Barina (VIN S/T) 2011 Buick Excelle 2011 Buick Regal (China) 2011 Camaro (VIN F) 2011 Canyon, Colorado (VIN S/T) 2011 Caprice PPV 2011 Captiva Sport 2011 Corvette (VIN Y) 2011 Cruze 2011 CTS (VIN D) 2011 DTS (VIN K) 2011 Equinox, Terrain (VIN L) 2011 Express, Savana (VIN G/H) 2011 HHR (VIN A) 2011 Impala (VIN W) 2011 Insignia 2011 LaCrosse (China) 2011 Lucerne (VIN H) 2011 Malibu (VIN Z) 2011 Orlando 2011 Regal (VIN G) 2011 Sierra, Silverado (VIN C/K) 2011 SRX (VIN N) 2011 STS (VIN D) 2011 VE/WM - Sedan, Ute, Sportwagon, Caprice, Lumina, Omega, VXR8 2011 Volt 2012 Acadia, Enclave, Traverse (VIN R/V) 2012 Alpheon (2706)2012 Ampera, Volt (VIN R) (Europe) 2012 Antara, Captiva 2012 Astra-J (2857)2012 Avalanche, Escalade, Suburban, Tahoe, Yukon (VIN C/K) 2012 Aveo Classic, Barina Classic (VIN T) 2012 Aveo, Sonic (2777)2012 Barina (2774)2012 Buick Excelle (2861)2012 Camaro (VIN F) 2012 Canyon, Colorado (VIN S/T) 2012 Caprice PPV 2012 Captiva Sport 2012 Chevrolet Cobalt (2809)2012 Colorado (Other IO), S10 (South America) 2012 Corvette (VIN Y) 2012 Cruze (2863)2012 CTS (VIN D) 2012 Equinox, Terrain (VIN L) 2012 Express, Savana (VIN G/H) 2012 Impala (VIN W) 2012 Insignia (2707)2012 LaCrosse (China) (2710)2012 LaCrosse (VIN G) (2709)2012 Malibu (VIN Z) 2012 Opel Combo-D 2012 Optra, Viva (VIN J) 2012 Orlando (2859)2012 Regal (China) (2711)2012 Regal (VIN G) (2708)2012 Sierra, Silverado (VIN C/K) 2012 Sonic (US/Canada) (2775)2012 SRX (VIN N) 2012 VE/WM - Sedan, Ute, Sportwagon, Caprice, Lumina, VXR8 2012 Verano (US/Canada) (2816)2012 Volt (VIN R) 2012 Zafira-C (2860)2013 Acadia, Enclave, Traverse (VIN R/V) (3206)2013 Alpheon (3094)2013 Ampera, Volt (VIN R) (Europe) (3211)2013 Antara, Captiva (5376555)2013 Astra-J Convertible/Coupe (5376567)2013 Astra-J (5376577)2013 ATS (VIN A) (3086)2013 Avalanche, Escalade, Suburban, Tahoe, Yukon (VIN C/K) (3088)2013 Aveo, Sonic (Africa, Middle East, AP, South America, CKD, Mexico) (5376711)2013 Aveo, Sonic (Europe) (5376704)2013 Barina (5376837)2013 Camaro (VIN F) (3106)2013 Caprice PPV (3105)2013 Captiva Sport (3101)2013 Cobalt (3107)2013 Colorado, Colorado 7, S10, Trailblazer (5392270)2013 Combo-D 2013 Corvette (VIN Y) (3104)2013 Cruze (Global) (5377099)2013 CTS (VIN D) (3085)2013 Encore (China) (5377162)2013 Encore, Trax (North America) (5377181)2013 Equinox, Terrain (VIN L) (3100)2013 Excelle (5377155)2013 Express, Savana (VIN G/H) (3103)2013 Impala (VIN W) (3102)2013 Insignia (3098)2013 LaCrosse (China) (3095)2013 LaCrosse (VIN G) (North America) (3090)2013 Malibu (China) (3096)2013 Malibu (Europe, Other IO and South America) (2713)2013 Malibu (North America) (3093)2013 Mokka, Trax, Tracker (Europe) (5377179)2013 Onix (3166)2013 Orlando (Global) (5377530)2013 Regal (China) (3099)2013 Regal (VIN G) (North America) (3089)2013 Sierra, Silverado (VIN C/K) (3087)2013 Sonic (US/Canada) (5377994)2013 Spark (US/Canada), Barina Spark (Automatic Transmission) (5421555)2013 Spin 2013 SRX (VIN N) (3201)2013 Trax, Tracker (Africa, Australia, Middle East, South America) (5377156)2013 VE/WM Ute, Caprice, Lumina 2013 Verano (US/Canada) (5377996)2013 Volt (VIN R) (North America, Holden) (3210)2013 XTS (China) (3092)2013 XTS (North America) (3091)2013 Zafira-Tourer FeaturesCompact design makes it lightweight and portable, easy to carry.Checking the pressure condition of the tyre in the real time.The tire pressure sensor on models in & after 2012 can be read, only with some specified diagnostic tools.With diagnostic sensing function.It is universal, suitable for most car.Note: The package does not include the charger and battery, please buy them by yourself.SpecificationType:TPMS relearn tool for GMMaterial: high plastic & metalHardware Version:OEC-T5Software Version: EL-50448Power:9WVoltage:12VOBD Interface:OBDIISupported System:TPMSVehicle Type:Passenger VehicleSpecial Features:Car Tire Pressure Monitor SensorSize:6.02*2.09*1.38in(15.3*5.3*3.5cm)Weight:145g(5.1oz)How to Use The tire pressure sensor on models in and after 2012 can be read, only with some specified diagnostic tools. Before tire pressure monitoring system works normally properly, the body control module will record ID information of each position in the tire pressure sensor; and use the following methods to read the tire pressure sensor. After replacing a tire or wheel speed sensor. Please refer to the specific methods as follows: Step 1 - Enter leaning modeSet the gearshift lever to "P"Put the ignition switch to "ON"Enter the interface of tire pressure display by DICDIC shows "Press Set / Ctrl to re-learn"Press "Set / Ctrl"The turn signal is lighted for 3 seconds and the horn beep sound twice to enter the learning mode Step 2 - Read tire pressure sensor informationStart from the front-left wheelMake the J-46079 or Diagnostic Tool EL-50448 antenna up against the valve core position & close to the rim of the tire sidewallEl-50448 tire pressure tool starts by the start switchSuccessful to read the tire pressure sensor information when the horn bleeps once Step 3 - Same method to read other tire pressure informationFollow the instruction above to read tire pussure of the front-right, rear-right, rear-left wheelsTurn signals is lighted for 3 seconds and the horn bleeps twice when the learning is complete Package1x EL-50448 tool ShippingPaymentReturnContact usFeedbackShippingWe ship package directly from our LA warehouse by UPS first Class(2-5working days) and USPS first Class(2-5working days). if you want to choose faster shipping way like Overnight Shipping .Please contact us ASAP. Tracking number will be provided. Final purchase price do not cover any applicable tax or duty that might be charged by customs .Buyers are responsible for such charges.Notes：We won't ship to VIRGIN ISLANDS, PUERTO RICO, ALASKA, HAWAII and GUAM for free. We need to calculate the shipping fee additionally. BUY IT, We will contact you and calculate for you. PaymentYou may pay for your items using payment methods such as the following: Certain credit or debit cards (VISA, MasterCard, American Express, and Discover),PayPal,Google Pay,Apple Pay,Direct debit, or eBay coupons, gift cards, etc. (if applicable). ReturnIn the event that you would like to return your purchase, we allow returns that are processed within the defined return date (the return date is to be found in the return policy/shipping and handling section)Please contact us via ebay message before you open the return requests.The item must be return in good condition with original packaging and accessories, and never installed or mounted.Contact usNote: If u have any problem, complaint ,advise ,please give us eBay message First Before Any Feedback. We will reply your message and solve your problem during working time(Except Holiday)ASAP.FeedbackCustomer satisfaction is very important to us. If you have any problem with your order,please contact us and we will do our best to make you satisfied, please do not leave a negative feedback before we resolve your problem.We guarantee that your issue will be solved quickly.As long as you are happy with your purchase of , please leave us a positive feedback.Your feedback is very important to us it affects our search placement on eBay. We will leave a positive feedback for you in return automatically once we receive your feedback. Thank you for visiting our ebay store!

Continue lendoEL-50448 OEC-T5 Auto Tire Pressure Monitor Sensor Activation Tool TPMS For GM F