ATV

Description: 1.AUTOOL CT180 is an intelligent injector cleaning & testing equipment with intelligent control. The whole process can be operated by the touch screen or rotary knob to complete. 2.Equipped with an ultrasonic cleaning tank, AUTOOL CT180 Fuel injector cleaner and Tester can generate an oscillating signal to the injectors to remove the stubborn carbon deposits from the injectors. It is possible to test injectors under different conditions, such as Sprayability Test, Leakage Test, Injecting Flow Test, etc. Uniformity/Sprayability test Uniformity test is to find out if the flow of different injectors meets the requirement or specifications under the same working condition. This test can reflect the comprehensive influences on the injector caused by electrical nature, bore variation and clogging. Sprayability test is to inspect the spraying performance by observing the injectors. Leakage test Leakage test is to inspect the sealing conditions of the injector needle valve under system pressure and to find out if the injector is dribbling. Bright background lights can help to clearly see the various conditions during injector testing. Injecting flow test Injecting flow test is to check if the injecting flow in 15 seconds meets the specifications for injecting amount. The deviation reflects the wear or clogging in the injector, instead of electrical parameter variation. Automatic test Autotest contains all of the above tests. According to the preset mode, it can simulate the working condition of the engine and automatically test the comprehensive performance of the fuel injectors. Injector Testing 1. First add the test fluid, then install the injectors on the fuel distributor, and fix them with bolts. 2. Different functions can be selected to test to see if any of the injectors are leaking or blocked. Smart touch screen design Designed with a 4" high resolution touch screen, all testing functions can be completed by touch screen operation. After testing, the test fluid can be drained out by pressing the button on the control panel. Test level gauge & Pressure gauge It allows you to observe the amount of test fluid and the test fluid can be recycled. It allows you to observe the pressure during test to avoid damage to machine or injectors caused by excessive pressure. Ultrasonic cleaning It sends signals to the injectors through the pulse signal line, using the cleaning fluid with the ultrasonic vibration so as to completely remove the carbon and impurities inside the injectors.Clean Multiple Injectors At The Same Time Ultrasonic Cleaning: 1. Add the cleaning fluid and put the injectors into the ultrasonic cleaning bath. 2. Connect the pulse signal lines and select the item 1 Ultrasonic Cleaning function to start.Ultrasonic cleaning bath size: 153x87x67(mm), power: 70W. Functions: A variety of test parameters can be set to simulate injector testing under various operating conditions. Backlight Design & Level Gauge: The glass tube can be observed through the level gauge during the test, so that the injector flow can be determined whether the flow is normal. At the same time, the backlight can assist in making the observation more carefully. It is an expert in injector solutions, featuring 7 injector-specific functions 01. Ultrasonic cleaning: It can clean several injectors at the same time and completely remove carbon deposits from the injectors. 02: Uniformity/Sprayability test: To test the uniformity of injecting amount of each injector, and to monitor the spraying status of each injector with the help of backlight. This test is also for reverse flush. 03: Leakage test: To test the sealing and dribbling conditions of injectors under system pressure. 04: Injecting flow test: To check the injecting amount of the injector in 15 seconds of constant injection. 05: Automatic test: To test injectors by simulating different working conditions. 06: No-disassembly cleaning: Direct cleaning without disassembling the injectors, this function is an additional function, which requires special adapters. 07. Settings: The Settings interface is used to set the default values whenever the device is started. Easy To Operate:Cleaning Sequences:NOTE: Test liquid and detergent won’t be provided by the manufacturer.1.Remove the injector from the vehicle engine to check the o-rings for damage. Replace the damaged O-ring with another same type O-ring to avoid leakage during testing.2.Put the outside of injectors in gasoline or detergent, and wipe them with soft cloth after cleaning the outside oil sludge carefully.3.Check the liquid level and refill test liquid when necessary. Fill the test liquid through the filler on the side of the unit and observe the liquid level in the fuel level viewer.Do NOT exceeding the Max line.4.Turn on the power switch on the left side of the Cabinet.5.Fill ultrasonic detergent into the ultrasonic cleaning launder so that the needle valve of the injector is covered by the detergent.6.Connect the injectors with the correct couplers. Testing Sequences:A complete cleaning and testing sequence shown below should be followed:Ultrasonic Cleaning——Uniformity/Sprayability Test——Leakage Test——Injecting Flow Test——Automatic Test.（Please Refer To The Manual For Detailed Operation Steps.） Specification:Power Supply: AC 110V/220V±10%, 50/60Hz.Equipment Power: 150W.Ultrasonic Cleaner Power: 60W.Pressure Unit: Bar, Psi, Kpa, mmHg, Kg/cm².Working Pressure: 0~10bar.Simulated RPM Range: 20~10000RPM.Pulse Width: 0.5ms~25ms.（Stepping 0.1ms）Uniformity/Sprayability Test Time: 1~20Min.Leakage Testing Time: 1~30Min.Injector Testing Time: 3~120s.Automatic Draining Testing Liquid Time: 60s.Main Unit Size: 270*310*340MM（10.6*12.2*13.4 Inch）.Package Size: 300*340*400MM.Package Weight: 12KG（26.46lb）. Working Conditions: Temperature: -10~+40℃.Relative Humidity: ＜85%.Intensity Of Outer Magnetic Field: ＜400A/m.NOTE: No Flame Within 2 Meters. Packing list 1pc * AUTOOL CT180 Fuel Injector Cleaner Tester Main Unit; 1pc* Ultrasonic cleaning set (including tray, cover and bracket) 2pcs * Power Cable(for connecting power supply); 1pc* Toolbox (for accessory storage) 1pc * User Manual(Instructions) 4pcs* injector pulse signal line (used to connect the signal line connector of product end and the injector pin to transmit the pulse signal) 20pcs* O-ring gasket Φ7.1*2.65 (for sealing the joint between injectors and oil separator) 4pcs* O-ring gasket Φ15*2.65 (for sealing the junction between injectors and oil separator) 3pcs* Plugs for oil separator(used to block the holes on the oil separator) 4pcs * Top inlet connectors (M12 coarse thread)(for connecting the top of the injector and the oil separator hole) 4pcs * Top inlet connectors (Swiss thread) (for connecting the top of the injector and the oil separator hole) 4pcs * Top inlet connectors (Φ10.5)/(Φ13.5)/ (Φ16.2) (for connecting the top of the injector and the oil separator hole) 1pc* Oil separator assembly set(includes fuel distributor, adjusting bolt, knurled nut, compression screw) 1pc* Filling funnel (for adding test fluid) 1pc*Oil drain wrench (used to install and remove oil drain screw) AUTOOL FUEL INJECTOR CLEANER Model CT150 CT160 CT180 CT500 Power Supply AC110V/220V±10% AC110V/220V±10% AC110V/220V±10% AC110V/220V±10% Frequency 50HZ/60Hz±0.5 50HZ/60Hz±0.5 50HZ/60Hz±0.5 50HZ/60Hz±0.5 Cleaning Frequency 28KHZ 40KHz 28KHZ 28KHZ Fuel Tank Capacity 2000ml 1300ml 2100ml 2000ml Ultrasonic Cleaner Power 70W 70W 60W 70W Speed Range 0-7500r/min 0-7500r/min 0-7500r/min 0-7500r/min Main Unit Dimensions 300*220*320mm 292*260*273mm 270*310*340mm 405*380*430mm Main Unit Weight 9.3kg 8kg 8.8kg 15.9kg