AUTOOL CT200

AUTOOL CT200is an injector cleaner and tester machine that combines ultrasonic cleaning technology with oil pressure control cleaning and inspection technology. It can simulate various working conditions of the engine to clean and test the injectors. It can support 6-cylinder injectors at the same time, saving time, and efficiency. Also supports testing of fuel injectors for most cars and motorcycles in the market. Since its launch, AUTOOL CT200 model has been widely received and approved by professional auto repair technicians. It is an expert in Injector solutions, featuring 12 injector-specific functions01. Ultrasonic cleaning: It sends signals to the injectors through the pulse signal line, using the cleaning fluid with the ultrasonic vibration so as to completely remove the carbon and impurities inside the injectors.02. Idle speed test (0-20ms): Simulate the engine idling speed and test the state of the fuel injector.03. Medium speed test (0-7.5ms): simulate the engine running at medium speed and test the state of the fuel injector.04. High-speed test (0-4ms): Simulate the high-speed performance of the engine and test the state of the fuel injector.05. Acceleration test: Simulate the acceleration state of the car and test the performance of the fuel injector.06. Shift speed test: Simulate the shifting state of the car and test the working performance of the fuel injector.07. Leakage test: Test the sealing condition of the fuel injector.08. Idle dpeed sprayability Test: Simulate the engine idling state and test the spraying performance of the fuel injector.09. Medium speed sprayability test: Simulate the engine medium-speed state and test the spraying performance of the fuel injector.10. High-speed sprayability test: Simulate the high-speed state of the engine and test the spraying performance of the fuel injector.11. Reverse flush: Reverse flush is a way to clean the injectors with the test liquid flowing from the outlet to the inlet of the injector. Reverse flush may remove the dirt inside the injector or the injector Strainer (Only for the top fuel supply injector).12. No-disassembly cleaning: Direct cleaning without disassembling the injectors, this function is an additional function, which requires special adapters.Ultrasonic Cleaning Ultrasonic Wave Injector Cleaner and Tester works by sending an ultrasonic vibration signal to the injector nozzle through the pulse signal line, which makes the stubborn carbon deposit jitter strongly and removes more thoroughly.Wide Range of Applications With its wide range of applications, the AUTOOL CT200 Injector Cleaning Tester is able to support the majority of the injector cleaning and testing needs of automobiles and motorcycles on the market.Smart Panel Design Through the precise scheduling controlled by microcomputer and the intuitive digital display interface, it realizes the fully automatic cleaning and comprehensive inspection of the injector as well as the real-time monitoring of the dynamic value of the injector, which is convenient for you to view the details of the adjustment parameters.Fuel Injector TestInjector flow uniformity and sprayability test: This section is designed to ensure that the injector's spraying effect is uniform and the spraying performance is stable, thus ensuring full combustion of fuel and stability of power output. Leakage test: Through strict inspection of the injectors for leakage to ensure good sealing performance and prevent performance degradation or safety hazards caused by leakage. Injection Flow Test: This test is used to accurately measure the amount of fuel injected by the injector to ensure that the engine is supplied with the right amount of fuel under different operating conditions.Reverse Flush Cleaning & On-vehicle CleaningNo disassembly or cleaning is required: The unit comes with a variety of adapters for easy cleaning of the injectors on your vehicle. Flushing in the opposite direction: Reverse flushing is a method of cleaning an injector by testing the flow of the liquid from the injector outlet to the injector inlet. Removes dirt from the inside of the injector or injector filter in the reverse direction (for top injectors only)Supports 4 / 6 cylinder operationAThe AUTOOL CT200 Injector Cleaning Tester, a highly efficient 6-cylinder injector cleaning machine, is capable of cleaning and testing six injectors at the same time. However, its adaptability goes far beyond that, as it is also perfectly suited for 4 and 8 cylinder engines. When you apply it to 4-cylinder engines, please plug the two connectors inside the machine to ensure precise and safe operation. If you are working on an 8-cylinder engine, it is recommended that you divide the injectors into two groups of four and perform two cleaning tests each to ensure that each injector is thoroughly cleaned and tested.Pressure gauge It is used to display the output pressure of the injector during the test, and to control the test fluid output state of the injector by adjusting the pressure value.Level gauge To observe the volume of test fluid, be careful not to add more than the maximum amount to avoid damage to the machine or syringe due to excessive pressure.Recovery valves The cleaning and testing fluids are recycled through the valve and can be reused, saving you money and avoiding damage to the product caused by liquids left in the tank for long periods of time.How do I choose a cleaning solution? We recommend that you use a specialized syringe cleaner that is readily available at your local supermarket. It is usually very corrosive and flammable and should be used away from sources of ignition and avoided in contact with skin!How do I choose a test fluid? We recommend using a specialized automotive injector test fluid. If this is not available locally, industrial alcohol with an alcohol content of more than 75% can be used instead (usually the test fluid is a colorless, clear, non-irritating odor liquid).Note:Only cleaning liquid can be added to the ultrasonic tank. Glass test tubes can only add industrial alcohol as the test liquid .Please do not confuse these 2 liquids and do not add other liquids. If you are not sure if the liquid is correct, please contact me in advance with picturesPacking list1pc * AUTOOL CT200 Fuel Injector Cleaner Tester Main Unit; 1pc * Ultrasonic Cleaning Bracket(for placing the injectors during cleaning); 2pc * Drain Valves(For recovering the cleaning and test fluid ); 2pc * Fixing rods(For fixing the oil separator); 2pc * Fixing Nuts(For fixing the oil separator); 6pc* Reverse flush connectors φ15.8mm(for connecting the bottom of the injector and the oil separator hole) 6pc * Conical top inlet connectors φ10.5mm&13.6mm (for connecting the top of the injector and the oil separator hole) 6pc* Special injector gaskets(for auxiliary installation of special fuel injectors) 5pc * Special plugs for oil separator(used to block the holes on the oil separator) 5pc * Special injector seals (for auxiliary installation of special injectors) 1pc * Ultrasonic Cleaning Cover(for keeping the cleaning bath clean) 1pc * Power Cable(for connecting power supply) 6pc *Adapter cables(For transferring the pulse signal line connector, instead of connecting the injector signal input pin) 1pc * Oil Separator(Distribution device for outputting pressurized test fluid to the injectors) 1pc * User Manual(Instructions)Please note the information regarding test fluids and cleaners：1. Prohibit the use of corrosive liquids as injector testing fluids. It is prohibited to add corrosive liquid directly into the glass test tube, which will damage the machine seals and injectors. 2. It is prohibited to use cleaning agent instead of test fluid, because the cleaning agent is corrosive, which will cause damage to the equipment and injector seals. 3. Prohibit the use of petrol instead of cleaning agent or test fluid, which is dangerous and can easily cause safety hazards. 4. It is forbidden to confuse the two liquids, cleaning agent or test liquid, in which the cleaning liquid is corrosive and can easily damage the machine seals. 5. Please put the cleaning liquid in the ultrasonic box for engine carbon cleaning. Put the test liquid or industrial alcohol into the glass tube for syringe test. MORE PRODUCTSMORE PRODUCTSMORE PRODUCTS 3 YEARS WARRANTY Delivery DetailsMORE PRODUCTS MORE PRODUCTS MORE PRODUCTS 3 YEARS WARRANTY Delivery Details