Foxwell NT630 Plus OBD2 Scanner ABS Bleeding SRS SAS Code Reader Diagnostic Tool

  • Autor do post:
  • Post publicado:
  • Categoria do post:
  • Comentários do post:0 comentário

Foxwell NT630 Plus OBD2 Scanner ABS Bleeding SRS SAS Code Reader Diagnostic ToolABS SRS Reset ScannerFoxwell NT630 Plus ABS & SRS Reset SAS Calibration Diagnostic Tool :[Foxwell NT630 Plus ABS & SRS Reset Tool Features]ABS Auto Bleed: The air will get inside when the brake system opened to replace components such as calipers, wheel cylinders, the master cylinder, or brake lines or hoses. To get a firm brake pedal, the air has to be removed by bleeding the brakes. This abs auto bleed scan tool will help bleed the brake, cycling the pump and valves during the bleeding process.Bidirectional Control/ Active Test: Do the active test on the ABS/Airbag system and components, including Auto Bleed Test/ Setup SDM Serial Number/ ABS Manual Control Tests/ ABS Motor Test/ ABS Version Test/ Actuator Tests, etc.4 Modules Diagnosis:Scan ABS/SRS/Airbag/ OBD2 modules error faults to check the issues that caused the warning light on and turn off the MIL after maintenance.ABS/ Airbag/ SRS Sensor Reset & Calibrate: Reading ABS and SRS/ Airbag error codes, point out the car issues and guide you to repair them. Besides the normal diagnostic functions that others can do, it will reset the ABS & SRS system after maintenance to let the ECU identify the new components to make it work normally.SAS(Steering Wheel Angle Sensor) Calibration: calibrates of the steering angle sensor and stores the current steering wheel position as straight-ahead in the sensor EEPROM. On successful calibration of the sensor, its fault memory is automatically cleared.Self-Check E-mission Condition: Scan all OBD2 modules, show the I/M readiness status and check if the vehicle is ready for the annual inspection of S-M-O-G test.[Foxwell NT630 Plus ABS & SRS Reset Tool Support Functions] --- ABS/SRS/ Airbag Bidirectional Control/ Active Test --- The abs scan tool code reader temporarily allows you to do bi-directional diagnostic tests on the system and components of anti-lock brake systems and air bags, sends commands to the integrity of abs srs systems or vehicle’s modules to test the working status without using the vehicle controls and and when you exit the test, the system/component returns to normal operation. (Note: All the functions mentioned are up to your vehicle condition, please confirm the compatibility before purchase!) Attention Please: 1. Before bleeding the brake system, make sure no diagnostic codes are presen. 2. Do not let the master cylinder run dry during the brake bleeding procedure. 3. After bleeding the brake system, check the brake pedal for excessive travel or a “spongy” feel. Bleed again if either condition is present.Auto Bleed Test, Automated Bleed, or Service Bleed – removes air from the internal brake fluid chambers after servicing the brakes.ABS Manual Control Tests – allows to manually control the actuators in order to test ABS motors, solenoids, solenoid enable relays, EMBs, and more.ABS Motor Test – allows to manually control the ABS pump motor.ABS Version Test – displays the name of the brake system and the ABS controller version number, software ID, and sequence value.Actuator Tests – allows to manually control the actuators in order to test AYC valves, inlet valves, outlet valves, pump motors, and TRACS valves.Automated Test - automatically commands each solenoid valve and the pump motor on and off to test for proper operation.Brake Bleed Preparation Test - prepares the brake lines for bleeding by clearing air from the modulator. The test rehomes all the ABS and TCS motors, cycles the TCS motors, and then returns all motors to the “home” position at the bottom of the bore.Setup SDM Serial Number (Air Bag Sensing and Diagnostic Module) - allows to program a new air bag serial number into the dash integration module (DIM). You use this test after installing a new air bag; otherwise a diagnostic trouble code will be set when you turn on the ignition.Function Test - automatically commands the ABS relay, valve solenoids, and pump motor on and off to test for proper operation. Gear Tension Relief Test - relieves tension from the ABS motor gears so you can separate the ABS motor pack from the ABS hydraulic modulator. Hydraulic Control Tests - allows to manually engage and disengage the ABS solenoids for troubleshooting the hydraulic functions. Idle Up Manual Control Test - allows to manually control the idle up actuators. Lamp Tests - allows to manually control the ABS or TCS warning or indicator lamps. Motor Rehome Test - prepares the brake lines for bleeding by clearing air from the modulator. The test returns all ABS motors to their “home” positions. Pump Motor Tests - allows to manually control the pump motor. Relay Test - allows to manually engage and disengage either the ABS or TCS relays in order to test relay operation. Requested Torque Test - allows to manually control the engine torque to test for proper operation of the traction control system (TCS). Solenoid Tests - allows to manually control the inlet and output valve solenoids. System Identification - displays information about the brake system, the vehicle, and the ABS controller. TCS Test - allows to control the pump motor in order to apply fluid pressure to the front wheel circuits. Traction Control System (TCS) Manual Control Tests - allows to perform motor tests and an adjuster assembly control test. Voltage Load Test - “loads” the ABS battery supply circuit to test for adequate battery capacity.[Foxwell NT630 Plus Support Language]The device only can install 2 languages , one is English , the other one you can choose from the following : English, Korea, Spanish, Portuguese, French, Thai, Hungarian, Swedish, Dutch, Japanese, Italian, Russian,German Full OBDII Engine Check Code Reader obd2 diagnostic code reader provides comprehensive OBDII diagnostics for global OBDII/EOBD vehicles, reads and clear codes, turns off MILs, requests and records live sensor data,ect.except live data reading. In addition, it supports all 10 OBDII test modes, includs the mode 6 test. Powerful graphing capability gives you the "real picture" of what's going on in the vehicle, which allows you focus on any suspicious or symptom-specific data parameters. $01 - Request Current Powertrain Diagnostic Data$02 - Request Powertrain Freeze Frame Data$03 - Request Emission-Related Diagnostic Trouble Codes$04 - Clear/Reset Emission-Related Diagnostic Information$05 - Request Oxygen Sensor Monitoring Test Results$06 - Request On-Board Monitoring Test Results for Specific Monitored Systems$07 - Request Emission-Related Diagnostic Trouble Codes Detected During Current or Last Completed Driving Cycle$08 - Request Control of On-Board System Test or Component$09 - Request Vehicle Information$0A - Request Emission-Related Diagnostic Trouble Codes with Permanent Status [Foxwell NT630 Plus OBD2 Engine Support Car List]Asian Car (2013-2019 model) for AU Ford ( For Australian Market Only ), for Acura, for Daewoo, for Honda, for Holden, for Hyundai, for Isuzu, for Infiniti, for Kia, for Lexus, for Mazda, for Mitsubishi, for Nissan, for Perodua, for Proton, for Scion, for Subaru, for Suzuki, for Toyota. European Car (2001-2019 model) For Audi, for Abarth, for Alfa-Romeo, for Aston Martin, for BMW, for Bugatti, for Bentley, for Citroen, for Dacia, for EU Ford, for Ferrari, for Fiat, for Jaguar, for Lamborghini, for Lancia, for Land Rover, for Maserati, for Mini, for Maybach, for Mercedes Benz, for Opel, for Peugeot, for Porsche, for Renault, for Rolls, for Saab, for Seat, for Skoda, for Smart, for Sprinter, for Vauxhall, for Volvo, for VW, for VWCV. American (USA) Car (1996-2019model) : for Chrysler, for Ford, for GM ( including brazilian car maker ) Doesn't Support UAZ,LADA,VAZ [Foxwell NT630 Plus Free Upgrade Forever !!!]NOTE: NT630 plus use new program to update. not foxscanner, please go to new website (check back of scanner) download FoxAssist. or you can contact me directly. 1. Go to the Foxwell official website :Choose your product ,Under the page,click the Download,then download FoxAssist Installer.zip update clients software. 2. Register foxwell account and complete the related information at FoxAssist client software . 3. Connect NT630 Plus with computer by USB, click "Activation" menu. 4. It can indentifies your sn number automatic, choose your sn number and click Activation 5. Go to "Download" page, choose all software, and then click "upgrade" 6. Wait several minutes, update will be done, enjoy new software [Package List]1 pc x Foxwell NT630 Plus1 pc x User's Guide1 pc x Memory Card1 pc x USB Cable1 pc x Diagnostic Cable1 pc x plastic case or carton box PaymentDelivery detailsTerms of salesAbout usContact usPayment We accept all common forms of payment such as Credit cards、Debit card、Google Pay ect. Please contact us if you need to use another method to pay. Payment should be made within 4 days after bidding ends. Otherwise a Unpaid Item case will be opened to you. We are not responsible for buyers’ local taxes. Please include your special requests in eBay note if there is any.Delivery detailsShipping methods: USPS First Class Mail Service /USPS Priority Mail Service/UPS Surepost SERVICE/ UPS GROUND SERVICE I will process your order within one business day (excluding holiday and weekend)If you have any problems, you can contact me first or local USPS, UPSTerms of salesPlease do not hesitate to leave us your PositiveFeedbackandgood review If you are satisfied with our productsIf youare unsatisfiedwith your purchase,please email us first to get a better solution before you leaveaneutralornegative feedback, we work hard to make sure every customer 100% satisfied and resolve any problem for you. Thank you for your kindness. About usWe are a professional Authorized dealers of AUTEL, LAUNCH,ANCEL,FOXWELL, OBDSTAR, AUTOPHIX, KZYEE, NEXAS,Autek ,WOYO,etc. We support remote assistance by TeamViewer if you have any difficulty in software installation. Contact usAny questions, you can feel free to contact me by ebay message or whatsapp.Due to time difference, I may not be able to reply immediately, but I will reply within 24 hoursPlease contact me first before giving negative feedback or opening case. Wish we can solve the problem peacefully. Working hours:0:00 am - 3:00 am Pacific Time, 6:00-9:00 pm Pacific Time, 11:00 pm - 12:00 pm Pacific Time. On Oct 15, 2024 at 04:20:10 PDT, seller added the following information:

Continue lendoFoxwell NT630 Plus OBD2 Scanner ABS Bleeding SRS SAS Code Reader Diagnostic Tool

Foxwell NT630 Plus Bi-directional OBD2 Diagnostic Scanner ABS Bleeding SRS SAS

  • Autor do post:
  • Post publicado:
  • Categoria do post:
  • Comentários do post:0 comentário

FOXWELL NT630 PLUS Automotive Bidirectional Car OBD2 Scanner Diagnostic for ABS SRS Engine NT630 Plus ABS(Anti Lock Brake System) and Airbag Reset Tool. And SAS Steering angle Sensor Calibration Tool Advanced Features ● Bi-directional test & actuate test ● Professional to diagnose ABS system,SRS Ai-rbag system & Engine system–leads to screens for diagnostic trouble code information, live data stream, ECU information etc. ● ABS bleeding- removes air from the internal brake fluid chambers after servicing the brakes. ● SRS fault codes read & clear & light reset ● SAS Calibration– leads to screens for steering angle calibration ● Auto VIN-leads to screens for identifying a car by automatic VIN reading. ● OBDII/EOBD – leads to OBDII screens for all 9 generic OBD system tests. ● Update– Lifetime free update through USB , no extra cost . ● Multi-languages :English , Spanish, Chinese ,Portuguese, French,Swedish, Dutch, Japanese, Italian, Russian, German, Korea 【👉TIPS:The abs scanner can NOT clear airbag crash data/collision data even replace the new airbag. NOT support programming/coding.】 This NT630 plus ABS(Anti Lock Brake System) and Airbag SRS , Engine systemdoes not only have extensive coverage of vehicles but also provides accurate and professional diagnosis of ABS and airbag faults. And SAS Steering angle Sensor Reset. Universal OBD II function check for all OBDII Car Engine ,Read and Clear Error Codes for 1996 or Newer America cars , after 2002 Europe car , after 2003 Asian cars . OBD2 Protocol. Special Functions : ABS Bleeding , SAS Calibration Special tests are bi-directional diagnostic tests on anti-lock brake systems and air bags. The tests let you to use the scanner temporarily activate or control a vehicle system or component, and when you exit the test, the system/component returns to normal operation. Some tests display a command to the operator. Typical special test options include: ● ABS Manual Control Tests – allows to manually control the actuators in order to test ABS motors, solenoids, solenoid enable relays, EMBs, and more. ● ABS Motor Test – allows to manually control the ABS pump motor. ● ABS Version Test – displays the name of the brake system and the ABS controller version number, software ID, and sequence value. ● Actuator Tests – allows to manually control the actuators in order to test AYC valves, inlet valves, outlet valves, pump motors, and TRACS valves. ● Autobleed Test, Automated Bleed, or Service Bleed – removes air from the internal brake fluid chambers after servicing the brakes.Tips : Special function doesn't fit for all car models , please confirm with us before purchase . IMPORTANT ● Before bleeding the brake system, make sure no diagnostic codes are present. ● Do not let the master cylinder run dry during the brake bleeding procedure. ● Do not allow brake fluid to contact the motor pack or the electrical connectors. ● Use a recommended brake fluid. Do not use silicone brake fluids in an ABS-equipped vehicle After bleeding the brake system, check the brake pedal for excessive travel or a “spongy”feel. Bleed again if either condition is present. ● Automated Test – automatically commands each solenoid valve and the pump motor on and off to test for proper operation. ● Brake Bleed Preparation Test – prepares the brake lines for bleeding by clearing air from the modulator. The test rehomes all the ABS and TCS motors, cycles the TCS motors, and then returns all motors to the “home” position at the bottom of the bore. ● Function Test – automatically commands the ABS relay, valve solenoids, and pump motor on and off to test for proper operation. ● Gear Tension Relief Test – relieves tension from the ABS motor gears so you can separate the ABS motor pack from the ABS hydraulic modulator. ● Hydraulic Control Tests – allows to manually engage and disengage the ABS solenoids for troubleshooting the hydraulic functions. ● Idle Up Manual Control Test – allows to manually control the idle up actuators. ● Lamp Tests – allows to manually control the ABS or TCS warning or indicator lamps. ● Motor Rehome Test – prepares the brake lines for bleeding by clearing air from the modulator. The test returns all ABS motors to their “home” positions. ● Pump Motor Tests – allows to manually control the pump motor. ● Relay Test – allows to manually engage and disengage either the ABS or TCS relays in order to test relay operation. ● Requested Torque Test – allows to manually control the engine torque to test for proper operation of the traction control system (TCS). ● Setup SDM Serial Number (Air Bag Sensing and Diagnostic Module) – allows to program a new air bag serial number into the dash integration module (DIM). You use this test after installing a new air bag; otherwise a diagnostic trouble code will be set when you turn on the ignition. ● Solenoid Tests – allows to manually control the inlet and output valve solenoids. ● System Identification – displays information about the brake system, the vehicle, and the ABS controller. ● TCS Test – allows to control the pump motor in order to apply fluid pressure to the front wheel circuits. ● Traction Control System (TCS) Manual Control Tests – allows to perform motor tests and an adjuster assembly control test. ● Voltage Load Test – “loads” the ABS battery supply circuit to test for adequate battery capacity Foxwell NT630 Plus Special Functions Airbag: 1. Read Airbag codes, the scanner finds out the airbags codes, points out the problem help you to fix it 2. Clear Airbag codes, the scaner erease the airbag code and turn off the airbag lights 3. Reset Airbag system Steering Angel Sensor Calibration SAS Calibration menu lets you perform calibration of the steering angle sensor, which permanently stores the current steering wheel position as straight-ahead in the sensor EEPROM. On successful calibration of the sensor, its fault memory is automatically cleared. OBDII/EOBD Function ● System Status ● Read Codes ● Freeze Frame Data ● Erase Codes ● Live Data ● I/M Readiness ● O2 Sensor Test ● On-board Monitor Test ● Component Test ● Vehicle Information ● Modules Present● Code Lookup ● Service $01 - request current powertrain diagnostic data ● Service $02 - request powertrain freeze frame data ● Service $03 - request emis-sion-related diagnostic trouble codes ● Service $04 - clear/reset emis-sion-related diagnostic information ● Service $05 - request ox-yg-en sensor monitoring test results ● Service $06 - request on-board monitoring test results for specific monitored systems ● Service $07 - request emis-sion-related diagnostic trouble codes detected during current or last completed driving cycle ● Service $08 - request control of on-board system, test or component ● Service $09 - request Vehicle Information Engine/SRS Ai-rbag/ABS diagnosis Vehicle Coverage: American (USA) Car ( after 1996-now model) : for Chrysler, for Ford, for GM, for BrazilGM, For Brazilfiat Asian Car ( after 2003 to now model) for Acura, for Daewoo, for Honda, for Hyundai, for Isuzu, for Infiniti, for Kia, for Lexus, for Mazda, for Mitsubishi, for Nissan, for Perodua, for Proton, for Scion, for Subaru, for Suzuki, for Toyota. European Car ( afer 2001-now model) For Audi, for Abarth, for Alfa-Romeo, for Aston Martin, for BMW, for Bugatti, for Bentley, for Citroen, for Dacia, for EU Ford, for Ferrari, for Fiat, for Jaguar, for Lamborghini, for Lancia, for Land Rover, for Maserati, for Mini, for Maybach, for Mercedes Benz, for Opel, for Peugeot, for Porsche, for Renault, for Rolls, for Saab, for Seat, for Skoda, for Smart, for Sprinter, for Vauxhall, for Volvo, for VW, for VWCV. China car (after 2008-now model)Special Functions Notice: ABS , SRS & SAS Special features are not compatible with all cars, please tell us the car VIN before purchase so as to confirm whether it is suitable for your car ,thanks ! ABS & Airbag Function " Support Car List : SAS Function " Support Car List : Update (Lifetime Free Update) Update requires Windows system : Win XP, Win 7, Win 8 & Win 10 With internet access, you will always have the latest bug fixes, new vehicles, newly added parameters and functionality at your fingertips. Through the USB cable connection to the PC, then register your foxwell ID. The application does all the work, syncing the latest software to your tool. NOTE: NT630 plus use new program FoxAssist to update. not foxscanner, please go to new website (check back of scanner) download FoxAssist. or you can contact me directly.1. Go to the Foxwell official website :Choose your product ,Under the page,click the Download,then download FoxAssist Installer.zip update clients software.2. Register foxwell account and complete the related information at FoxAssist client software .3. Connect NT630 Plus with computer by USB, click "Activation" menu.5. It can indentifies your sn number automatic, choose your sn number and click Activation6. Go to "Download" page, choose all software, and then click "upgrade"7. Wait several minutes, update will be done, enjoy new software Support Language :The device only can install 2 languages , one is English , the other one you can choose from the following :English, Korea, Spanish, Portuguese, French, Thai, Hungarian, Swedish, Dutch, Japanese, Italian, Russian,German Specifications: Brand: FOXWELL Model: NT630 Plus Color: black + orange Display: Backlit, 240*320 TFT color display OSD Language: English, French, German, Spanish, Dutch External Power: 8-18 Volts powered by vehicle battery Working Temperature: 0℃to 60℃ Storage Temperature: -20℃ to 70℃Package List: 1 * NT630 Plus Scan Tool 1 * Memory Card 1 * USB Cable 1 * Diagnostic Cable 1 * User Manual 1 * bag PaymentDelivery detailsTerms of salesAbout usContact usPaymentWe accept all common forms of payment such as Credit cards、Debit card、Google Pay ect. Payment should be made within 7 days after bidding ends.Otherwise a Unpaid Item case will be opened to you.Please include your special requests in eBay note if there is any.Delivery detailsOrder will be shipped within 1 business day after payment confirmed.We have warehouse in USA, From our US warehouse via UPS or USPS shipping. Delivery time varies from 2 to 5 business days.We will ship according to your eBay address. Please make sure it is correct and include phone number for delivery.If you do not receive your order in the estimated time, please contact us, we would do our best to serve you solve the problem. Please include your special requests in eBay note if there is any.Terms of salesReturn PolicyPlease return the item within 60 days after receiving if you are not happy with your purchasing.All returns are expected to be in original conditions, please email us first for return address and instructions. We are authorize distributor, our all items are 100% original and Our devices have warranty, 5 Year free repair for the devices. Please contact us firstly when you need warranty service.In case an item arrives faulty, please contact us as soon as possible and keep it unused.We will instruct you on how to return and get refund or replacement.If the item has been used, we have the right to decline your claim.Items should be returned on buyers' cost for repair or replacement.About usWho We Are? We are specialized dealer of On-Board Car Diagnostic tools and automotive electronics for more than 15 years. We are authorized first class distributor of Launch, Foxwell, Autek, Ancel, Innova, Autophix, Thinkcar, Kzyee brands, and more brands will be show in our store in near future. What Do We Have? We have office and warehouse in US to ensure fast shipment and after-sale service. We have more than 1000 employees devoting to customer satisfaction. Contact us 1:If youhave any problem about the goods, please contact us before leaving Neutral/Negative feedback.We promise to help you solve it asap, and make you feel satisfactory absolutely. 2: our business time:M-F: 9:30AM - 18:00PM BST (Beijing Standard Time) 3:Please leave us Positive Feedback and 5-stars★★★★★after you received our package you are satisfied with it. as you know, every seller works hard for the positive feedback. We will do the same as soon as we can too.

Continue lendoFoxwell NT630 Plus Bi-directional OBD2 Diagnostic Scanner ABS Bleeding SRS SAS

Bidirectional SRS ABS Bleeding SAS Oil EPB Reset OBDII Scanner Diagnostic Tool

  • Autor do post:
  • Post publicado:
  • Categoria do post:
  • Comentários do post:0 comentário

Foxwell Bidirectional SRS ABS Bleeding SAS Car OBD2 Scanner Diagnostic Scan ToolFOXWELL NT630 PLUS Automotive Bidirectional Car OBD2 Scanner Diagnostic for ABS SRS Engine ABS Bleeding and Airbag Reset Tool and SAS and EPB and Oil Reset Advanced Features● ABS & SRSBi-directional test & actuate test ● Professional to diagnose ABS system,SRS Ai-rbag system & Engine system–leads to screens for diagnostic trouble code information, live data stream, ECU information etc.● Oil Reset-Allows you to reset the service lamps on the instrument cluster. The Service Indicator System is designed to alert the driver when the vehicle is due for a service. ● ABS bleeding- removes air from the internal brake fluid chambers after servicing the brakes. ● SRS fault codes read & clear & light reset ● SAS Calibration– leads to screens for steering angle calibration● EPB Reset– Electronic Park Brake Reset ● Auto VIN-leads to screens for identifying a car by automatic VIN reading. ● OBDII/EOBD – leads to OBDII screens for all 9 generic OBD system tests. ● Update– Lifetime free update through USB , no extra cost . ● Multi-languages :English , Spanish, Chinese ,Portuguese, French,Swedish, Dutch, Japanese, Italian, Russian, German, Korea 【👉TIPS:The abs scanner can NOT clear airbag crash data/collision data even replace the new airbag. NOT support programming/coding.】 ABS & SRS Bi-directional Control Function(Actuation Test) Command Particular Operations on the VehicleThis device with bi-directional technology, not only can diagnosis a problem but can also take measures to begin the repair. The nt630 plus can activate and actuate ABS & SRS modules. It's necessary when you want to see whether an actuator or sensor is working as it should. Support ABS SRS Diagnose: Read and Clear Codes of ABS & SRS Electronice Modules, Help you accurately identify car’s problem!This option allows you to detect whether the system parameters are normal or not. Include : ABS System,Engine System,SRS System , Read and erase codes for all available systems, turn off MIL light (Indicator light), display live data in text, graph & analog for easy data review. 5 Special Functions : Oil Reset, EPB, ABS Bleeding, SAS Calibration, SRS Reset. 1.Oil Lamp Reset ServiceAllows you to perform reset for a new calculation of Engine Oil Life system once changed the oil.2.EPB Electronic Park Brake ResetIt is important in the maintenance of electronic braking system's safety and efficiency. 3.ABS BleedingABS brake bleeding to get a firm brake pad after air exhaustion after repair ABS pump system. 4.SAS Steering Angel Sensor ResetHelps clear the fault steering angle sensor memories and plays an important role in the steering angle sensor calibration. 5. SRS ResetReads airbag light codes, resets SRS codes after troubleshooting. NOTE: Airbag crash data cannot be cleared OBDII/EOBD Function ● System Status ● Read Codes ● Freeze Frame Data ● Erase Codes ● Live Data ● I/M Readiness ● O2 Sensor Test ● On-board Monitor Test ● Component Test ● Vehicle Information ● Modules Present● Code Lookup ● Service $01 - request current powertrain diagnostic data ● Service $02 - request powertrain freeze frame data ● Service $03 - request emis-sion-related diagnostic trouble codes ● Service $04 - clear/reset emis-sion-related diagnostic information ● Service $05 - request ox-yg-en sensor monitoring test results ● Service $06 - request on-board monitoring test results for specific monitored systems ● Service $07 - request emis-sion-related diagnostic trouble codes detected during current or last completed driving cycle ● Service $08 - request control of on-board system, test or component ● Service $09 - request Vehicle Information Vehicle Coverage: American (USA) Car ( after 1996-now model) : for Chrysler, for Ford, for GM, for BrazilGM, For Brazilfiat Asian Car ( after 2003 to now model) for Acura, for Daewoo, for Honda, for Hyundai, for Isuzu, for Infiniti, for Kia, for Lexus, for Mazda, for Mitsubishi, for Nissan, for Perodua, for Proton, for Scion, for Subaru, for Suzuki, for Toyota. European Car ( afer 2001-now model) For Audi, for Abarth, for Alfa-Romeo, for Aston Martin, for BMW, for Bugatti, for Bentley, for Citroen, for Dacia, for EU Ford, for Ferrari, for Fiat, for Jaguar, for Lamborghini, for Lancia, for Land Rover, for Maserati, for Mini, for Maybach, for Mercedes Benz, for Opel, for Peugeot, for Porsche, for Renault, for Rolls, for Saab, for Seat, for Skoda, for Smart, for Sprinter, for Vauxhall, for Volvo, for VW, for VWCV. China car (after 2008-now model) Update (Lifetime Free Update) Update requires Windows system : Win XP, Win 7, Win 8 & Win 10 With internet access, you will always have the latest bug fixes, new vehicles, newly added parameters and functionality at your fingertips. Through the USB cable connection to the PC, then register your foxwell ID. The application does all the work, syncing the latest software to your tool. NOTE: NT630 plus use new program FoxAssist to update. not foxscanner, please go to new website (check back of scanner) download FoxAssist. or you can contact me directly.1. Go to the Foxwell official website :Choose your product ,Under the page,click the Download,then download FoxAssist Installer.zip update clients software.2. Register foxwell account and complete the related information at FoxAssist client software .3. Connect NT630 Plus with computer by USB, click "Activation" menu.5. It can indentifies your sn number automatic, choose your sn number and click Activation6. Go to "Download" page, choose all software, and then click "upgrade"7. Wait several minutes, update will be done, enjoy new software Support Language :The device only can install 2 languages , one is English , the other one you can choose from the following :English, Korea, Spanish, Portuguese, French, Thai, Hungarian, Swedish, Dutch, Japanese, Italian, Russian,German Specifications: Brand: FOXWELL Model: NT630 Plus Color: black + orange Display: Backlit, 240*320 TFT color display OSD Language: English, French, German, Spanish, Dutch External Power: 8-18 Volts powered by vehicle battery Working Temperature: 0℃to 60℃ Storage Temperature: -20℃ to 70℃Package List: 1 * NT630 Plus Scan Tool 1 * Memory Card 1 * USB Cable 1 * Diagnostic Cable 1 * User Manual 1 * Plastic Case

Continue lendoBidirectional SRS ABS Bleeding SAS Oil EPB Reset OBDII Scanner Diagnostic Tool

2024 MUCAR VO7S Bidirectional Car Diagnostic Scanner Tool Key Coding CANFD OBD2

  • Autor do post:
  • Post publicado:
  • Categoria do post:
  • Comentários do post:0 comentário

ThinkOBD500MUCAR BT200MUCAR CDE900 PROTHINKTOOL MINI2MUCAR CS6MUCAR VO8THINKSCAN PLUS S72024 MUCAR VO7S Bidirectional Car Diagnostic Scanner Tool Key Coding CANFD OBD2NOTE:MUCAR VO7S offers 3 years of free upgrades.What is the difference between MUCAR VO7 and MUCAR VO7S? MUCAR VO7S adds CAN-FD protocol to support more models【2024 Newest All-in-one Scanner】As the upgraded version of MUCAR VO6,The VO7S Car Diagnostic Scanner Provide ➤ Functional Tests & Bi-Directional Controls ➤Flash Hidden & VAG Guide Functions ➤【AutoAuth for FCA SGW】Works with Chrysler,Dodge,and Jeep after 2017 ➤ Setting & Changeover (adblue reset, unlock the engine after a collision, cancel ABS driving test, and more) for Benz ➤ Modification for BMW ➤ Customization ➤Personalization ➤ ECU Coding & Configurations ➤ 106+ Car Brands, and keep growing.【Bi-Directional Control/Active Tests】 The MUCAR VO7S bidirectional scan tool can output commands to a vehicle’s ECUs, read the ECU data, and monitor the operation of the actuators. Through active tests on certain components, such as fuel pumps, a/c fan, inside mirrors, headlamps, windows, and horns, this bidirectional scanner will let you quickly know whether a specific system, component, or subsystem is functioning properly or not, helping you locate the car issues precisely.【ECU Coding + Adaptation + Initialization + Matching】The MUCAR VO7Ss bidirectional obd2 scanner support ECU Coding to quickly match, learn, code any replaced ECU. Modify ECU and reveal hidden features for 99% cars in the market. Adaptive data for certain components after repairs or replacements.【28+ Maintenance Reset Functions】1.Throttle 2.Injector Coding 3. SAS 4. ABS 5. Oil 6. Gearbox 7. IMMO/Key Programming 8. Airbag 9. TPMS 10. Gear Learning 11. EPB 12. AFS 13. A/F 14. AdBlue 15. DPF 16. NOx Reset 17. EGR Bleed 18.IC 19. Coolant Bleed 20.Suspension 21. Tyre Setting 22. Seat Calibration 23.Windows Calibration 24.Sunroof 25. Language Set 26. Transport Mode 27. Stop/Start 28. BMS Note:Service functions vary by vehicle, please to check compatibilitybefore order‼【All Systems & Subsystems Diagnosis】The MUCAR VO7S OBD2 scanner diagnostic tool will automatically scan your entire vehicle's systems and subsystems including Body, Chassis, Powertrain, Fuel system, Light system, etc. It identifies systems and subsystems module information, reads fault codes, and generates a diagnostic report in as little as 120 seconds. You can access the system from the report menu to clear fault codes and live data graph,quickly locate vehicle faults and get them solved.【Intelligent Software to Keep Growing】MUCAR VO7S automotive diagnostic tool has powerful software ➤ Localized 17 Languages ➤ Coveage List ➤ AutoSearch Diagnose ➤ History Records ➤ Report Management ➤ OTA Upgrade ➤ 106+ Vehicle Brands Software to Keep Growing, VO7 scanner for car works on most OBD-II compliant cars after 1996 and upgrade new make up to 2022 models, compatible with OBD2/EOBD & CAN protocols, including most 12v cars, SUV, pickup, light duty truck, minivans.【Wireless & Bluetooth + High-End Configuration】The VO7 car scanner equipped with the powerful 1.8GHz processor, Android 8.1, 7”touchscreen, 32G ROM, 6000mAh battery,2.4GHz & 5GHz Wi-Fi connection;With the included Bluetooth 4.0 VCI dongle, experience wireless diagnostics with an operating range of up to 33 feet (10 meters).【Buy with Confidence:2-Year Warranty & 100% Original 】To make your purchase worry-free, this 100% original MUCAR scanner - The VO7 comes with 30-day free refunds and exchanges;If you think you receive an used or defective product,Please don't worry and contact us! If you are not pleased with your VO7 code reader and choose to return it, please kindly mark it unsellable to avoid an used one is resold again to other customers. Appreciate very much【CAN-FD protocol 】The MUCAR VO7S CAN FD adapter can diagnose vehicles using the CAN FD (CAN Flexible Data Rate) protocol. Newer vehicles can be easily diagnosed (MUCAR VO7S has been updated). Product Homepage Function 1. Intellignt diagnosis, automatic identification of vin, enter the diagnosis system 2. Maintenance service, maintenance service download, enter the system 3. MUCAR mall, subscription software, software upgrade, realize full-function diagnosis 4. Online upgrade , The software version can be updated 5. Vehicle files, save the data records of the detected vehicles, such as: report 6. Settings Intelligent diagnosis Insert the connector into the vehicle OBD interface, and the host can be connected to the connector. In the intelligent diagnosis mode, it can automatically read the vin identification vehicle information. If the special vehicle cannot be identified, the vehicle can also be manually selected for detection. After entering the system, the basic functions of the whole system of the vehicle can be tested (not including: action test, special function, cding), code reading, code clearing, real-time data flow chart display, combined display can be performed. Support obd full-function intelligent diagnosis. Purchase a model software separately, which can be upgraded to full-system full-function. MUCAR VO7S supports full system functionality, including bidirectional functions, ECU coding, and other special functions. NOTE: Free use of full functionality within 3 years, with a follow-up fee of $99 per year for 3 years.​ Support to ECU Coding The Coding function is used to re-flash the vehicle control modules.It is used to reprogram adaptive data for vehicle control modules after repairs or replacements of vehicle parts;Provide solutions for the issues of Drivability, Fuel Efficiency, Power Loss, Fault Codes, Durability of Mechanical Parts etc.;Brake the limitations and restrictions; make full use of the car hidden features, like change the chimes on car, set how many times the one-touch signal flickers for one touch, remember settings for Start/Stop systems, and more. Support Active Test (Actuation Test) If the actuator is normal, without using the vehicle’s controls, to get a significant boost in effectiveness: [ Turn on the radiator fan | Modulate the throttle | Open/close windows | Operate mirrors | Turn on/off the lights | Turn on/off the sound horn | Test door lock … ] MUCAR VO7S Lifetime Free All Cars Full System Diagnostic TOOL With superior all systems diagnoses, this multipurpose obd2 scanner can be used to read all available systems’ECU information to facilitate the vehicle diagnosis.The complete systems vary from different cars and they usually include engine, transmission, ABS, SRS, SAS, TPMS, EPB and chassis / body / electrical equipment system etc. ✅Examinate your car like a professional mechanical technician ✅Read DTCs from the vehicle’s all electronic control systems to locate problem areas, and offer solutions; ✅Erase the codes easily after DTCs retrieving and certain repairs have been carried out and turn off fault Indicator lamp; ✅Live data shows each sendor parameter item displayed in analog, text, waveform graph modes etc ✅The active test used to access vehicle-specific subsystem and component tests. MUCAR VO7S Lifetime Free All Cars 28 Reset Services 1. Oil Reset The lightening of the car maintenance light indicates that the vehicle needs maintenance.Reset the mileage or driving time to zero after the maintenance, so the maintenance light will go out and the system will start a new maintenance cycle. 2. Elec.Throttle Adaption Elec. Throttle Adaption is to utilize the car decoder to initialize the throttle actuator so that the learning value of the ECU returns to the initial state. 3.Steering Angle Reset To reset the steering angle, first find the relative zero point position for the car to drive in straight line.Taking this position as reference,the ECU can calculate the accurate angle for left and right steering. 4. Battery Matching This function enables you to perform a resetting operation on the monitoring unit of vehicle battery, in which the original low battery fault information will be cleared and battery matching will be done. 5. ABS Bleeding When the ABS contains air, the ABS bleeding function must be performed to bleed the brake system to restore ABS brake sensitivity. 6.Break-pad Reset lf the brake pad wears the brake pad sense line, the brake pad sense line sends a signal sense line to the on-board computer to replace the brake pad.After replacing the brake pad, you must reset the brake pad.Otherwise, the car alarms. 7.DPF Regeneration DPF regeneration is used to clear PM(Particulate Matter) from the DPF filter through continuous combustion oxidation mode (such as high temperature heating combustion, fuel additive or catalyst reduce PM ignition combustion) to stabilize the filter performance. 8.Gear Learning After the engine ECu, crankshaft position sensor,or crankshaft flywheel is replaced, or the DTC 'gear not learned' is present, gear learning must be performed. 9. IMMO Service To prevent the car being used by unauthorized keys, the anti-theft key matching function must be performed so that the immobilizer control system on the car identifies and authorizes remote control keys to normally use the car. 10. Injector Coding Write injector actual code or rewrite code in the ECU to the injector code of the corresponding cylinder so as to more accurately control or correct cylinder injection quantity. 11.TPMS Reset Note:Cooperate with wireless tire pressure diagnosis tool to realize TPMS activation, programming and learning functions 12. Suspension Matching This function can adjust the height of the body. When replacing the body height sensor in the air sus pension system, or control module or when the vehicle level is incorrect, you need to perform thisfunction to adjust the body height sensor for level calibration. 13. AFS Reset This feature is used to initialize the adaptive headlamp system. 14.A/T Learning This function can complete the gearbox self-learning to improve gear shifting quality. 15.Sunroof Initialization This function can set the sunroof lock off, closed when it rains,sliding /tilting sunroof memory function,temperature threshold outside the car etc. 16. EGR Adaption This function is used to learn the EGR valve after it is cleaned or replaced. 17. ODO Reset ODO reset is to copy, write, or rewrite the value of kilometers in the chip of odometer by using a car diagnostic computer and data cable, so that the odometer shows the actual 18. Airbag Reset This function resets the airbag data to clear the airbag collision fault indicator. 19. Transport Mode ln order to reduce power consumption, the following functions may be disabled, including limiting the vehicle speed, not waking up the door opening network, and disabling the remote control key, etc.At this time, the transport mode needs to be deactivated to restore the vehicle to normal. 20. A/F Reset This function is applied to set or learn Air/Fuel ratio parameters. 21. Stop/Start Reset This function is used to open or close the automatic start-stop function via setting the hidden function in ECU(provided that the vehicle has a hidden function and supported by hardware). 22. NOx Sensor Reset NOx sensor is a sensor used to detect the content of nitrogen oxides (NOx) in engine exhaust. lf theNOx fault is re-initialized and the NOx catalytic converter is replaced, it is necessary to reset the catalytic converter learned value stored in the engine Ecu. 23. AdBlue Reset (Diesel Engine Exhaust Gas Filter) After the diesel exhaust treatment fluid (car urea) is replaced or filled up, urea reset operation is required. 24.Seat Calibration This function is applied to match the seats with memory function that are replaced and repaired. 25.Coolant Bleeding Use this function to activate the electronic water pump before venting the cooling system. 26.Tyre Reset This function is used to set the size parameters of the modified or replaced tire. 27.Windows Calibration This feature is designed to perform door window matching to recover ECU initial memory, and recover the automatic ascending and descending function of power window. 28. Language Change This function is used to change the system language of the vehicle central control panel. Free Full OBDII Functions *-Read extensive current, pending and permanent codes in OBD system quickly *-Clear detected fault codes and turn off the Check Engine Light efficiently *-View graphical live data of vehicle's computer module(s) for easy analyses *-View the vehicle's operating parameters at the moment a DTC is detected *-Read I/M readiness status to have a vehicle inspected for state emissions compliance *-Perform O2 sensor test to check fuel efficiency and vehicle emissions *-Read the results of on-board diagnostic monitoring tests for specific components/systems *-Retrieve the vehicle information of VIN, CINs, and CVNs completely *-Perform the component Test by allowing initiating a leak test for the vehicle's EVAP system 4 IN 1 Scientific Data Management: Live Data Stream Graph & Record Data & Diagnosis Record Playback & Print Report The professional vehicle scanner tool can scientific graph data, record data, play back data, freeze frame,and print reports. In the real-time diagnosis process, important diagnosis information can be instantly stored in the memory, including reading of fault codes and frozen frames and real-time data streams. After real-time diagnosis is completed, Diagnosis function record playback, the diagnosis information and process previously saved in the memory can be replayed to facilitate the analysis of various data information. One-click generation of a diagnosis report after diagnosis will help users quickly solve problems, avoid blind maintenance, and save money/time. MUCAR VO7S Support 19 Multi-Langauge English, French, German, Italian, Spanish, Portuguese, Japanese, Russian, Polish language, Hungarian language, Arabic, Greek, Slovakia, Dutch language, Korean, Turkish language, Czech Support 128+ Worldwide Vehicle Coverage Support 126+ Car Brands and 1000+ Vehicles USA: For BXGM,For CHRYSLER, For AUSTFORD, For GM,USAFORD EUROPE: For ASTONMARTIN,For AUDI,For BENZ,For BMW,For BXFIAT,For CITROEN,For FERRARI,For FIAT,For GAZ,For LANDROVER,For MASE,RATI,For OPEL,For PAZ,For PEUGEOT,For PORSCHE... Austrillia: For AUSTFORD,For AUSTHOLDEN Asia: For BAIC,For CHANGAN,For CHANGCHENG,For CHANGHE,For DAEWOO,For DAIHATSU,For DFXK,For FLYER,For FUTIAN,For HAFEL For HMAZDA,For HONDA,For HUACHEN,For HYUNDAI,For IKCO,For INDIANMARUTI,For INDIANTATA,For ISUZU,For IVECO.IZH,For JACTY JIAO,For JINLONG,For JOYLONG,For JPISUZU,KIA,For LIFAN, For LIUWEITY ,For LUXGEN,For MAHINDRA,For MALAYSIA PERODUA,For MALAYSIA PROTON,For MARUT,For MAXUS,For MAZDA,For MITSUBISHI... How to Register/Update MUCAR VO7Ss 1.Initial Use 2.Turn on the Machine 3.Language Setting 4.Connect WIFI 5.Choose Time Zone 6.User Agreement 7.Create an Account 8.Typing in Business Information Product Parameters: Display Screen :7-Inch/TFT(IPS) Connection :Bluetooth RAM:2G ROM:32G Working Temperature : 32℉~122℉ Storage Temperature: -4℉~144℉ Packing List: 1*MUCAR VO7S Host 1*Diagnostic dongle 1*Charging cable 1*Multi-Language ManualMUCAR VO8MUCAR VO7SMUCAR VO7MUCAR VO6THINKCAR Thinktool miniAdvantage-1Full System Diagnosis For FreeFull System Diagnosis For FreeFull System Diagnosis For FreeFull System Diagnosis For FreeFull System Diagnosis For FreeAdvantage-234+ Reset Services28+ Resets Functions28+ Resets Functions28+ Resets Functions28+ Resets FunctionsAdvantages 3Bidirectional FreeBidirectional FreeBidirectional FreeBidirectional (pay for $49.95)Bidirectional (pay for $49.95)Battery9450mAh6300mAh6300mAh6300mAh6300mAhBrandMUCARMUCARMUCARMUCARThinkCarDisplay8 inch Touch Screen7 inch Touch Screen7 inch Touch Screen5.99 inch Touch Screen5.99 inch Touch Screensupported protocolsISO 14230-4 KWP/ 15765-4 CAN/ ISO 9141-2IS0/ SAE J1850 VPW/ SAE J1850 PWMCANFD Protocol/ ISO 14230-4 KWP/ 15765-4 CAN/ ISO 9141-2IS0/ SAE J1850 VPW/ SAE J1850 PWMISO 14230-4 KWP/ 15765-4 CAN/ ISO 9141-2IS0/ SAE J1850 VPW/ SAE J1850 PWMISO 14230-4 KWP/ 15765-4 CAN/ ISO 9141-2IS0/ SAE J1850 VPW/ SAE J1850 PWMISO 14230-4 KWP/ 15765-4 CAN/ ISO 9141-2IS0/ SAE J1850 VPW/ SAE J1850 PWMLanguagesSupport 28 LanguagesSupport 19 LanguagesSupport 19 LanguagesSupport 20 LanguagesSupport 17 LanguagesMemory2GB + 64GB2GB + 32GB2GB + 32GB2GB + 32GB2GB + 32GBOBD InterfaceCAN, EOBD, OBD, OBDIICAN, EOBD, OBD, OBDIICAN, EOBD, OBD, OBDIICAN, EOBD, OBD, OBDIICAN, EOBD, OBD, OBDIISupported SystemFull System, ABS, DPF, EPB, SAS, SRS, TPMS, EngineFull System, ABS, DPF, EPB, SAS, SRS, TPMS, EngineFull System, ABS, DPF, EPB, SAS, SRS, TPMS, EngineFull System, ABS, DPF, EPB, SAS, SRS, TPMS, EngineFull System, ABS, DPF, EPB, SAS, SRS, TPMS, EngineUpdate2-year free update3-year free update3-year free updatelifetime free Updatelifetime free UpdateOperating systemAndroid 8.0Android 10.0Android 10.0Android 10.0Android 10.0Warranty5 Years5 Years5 Years5 Years5 YearsPaymentDelivery detailsReturn detailsAbout usContact usPaymentWe accept the following payment methods To ensure that your items can be delivered as soon as possible, please fill in your payment information accurately! Thank youDelivery details All the products in my shop have local warehouses in the United States, Britain, France, Germany, and Australia. U.S. warehouses: They are located in two warehouses in New Jersey and California, both of which can be shipped within 1 day and delivered within 5 days. Australian warehouse: located in Sydney, we use Australia Post or fastways express delivery, and the products can be delivered within 3-7 days. UK warehouse, with self-built warehouse in Wolverhampton and stock in official ebayg warehouse, both can be delivered within 2 days . German warehouse, we use eBay official warehouse, there is sufficient inventory, and can be sent to 28 EU countries. It can be shipped the same day the order is placed, and delivered within two days within Germany. Return details We accept the following return methods Returns are accepted within 30 days of buyer receiving the item. (Does not include man-made damage or misuse). 100% Money Back Guarantee! All products will be 100% tested before shipping. Buyer has up to 30 days from date of receipt for replacement if item is defective due to postage handling. All shipping costs for returned products are paid by the seller, please contact us for the return address For any questions about defects, returns, item exchange requests, please contact us and send us a message before opening any kind of case or request. We are committed to making every customer 100% satisfied and solving any problems. We highly value and appreciate your business. Thanks. Returns are accepted within 30 days of delivery. Returned items must be in new, unaltered and resalable condition. Seller is not responsible for any labor costs, dealer store fees, or damage caused by incorrect installation.About us THINKCAR has an intelligent production workshop, which covers an area of more than 3,500 square meters, is equipped with a fully automatic packaging production line, and has intelligent warehouse management. THINKCAR products have gone through more than 50 production processes, passed 2 meters, 3 meters and other height drop tests, -4℉-140℉ high and low temperature tests, 8 hours vibration test, 1000 plug-in tests, 1000 circular wire throwing tests, Continuous working test for more than 48 hours, real vehicle test of more than 100 car brands, including most popular models in Europe, America and Asia. As the official store of Thinkcar, all products are 100% original products. THINKCAR is a company specializing in automotive diagnostic tools, committed to providing quality products and services. Contact us(1) We maintain high standards of excellence 5 Star feedback and strive for 100% Customer satisfaction. Please do not hesitate to leave us your positive feedback if you are satisfaction with our products ,delivery or services .(2)If you have any questions about our products or services, Please Contact usimmediately before you leave Neutral or Negative feedback,So that we can satisfactorily address your concerns. We will reply you within 12 hours, except on Weekends and Holidays.(3)If you have any needs for products, please contact us ,we’ll do our best solve with you . 4Solve any problems with you in friendly way after communication. Refund or Replacement will be provided as you like.Feature 1ECU CodingFeature 328 Reset ServiceFeature 2Bidirectional Control,Active TestFeature 5Support 19 Multi-LangaugeFeature 4Support CANFD ProtocolFeature 6128+ Worldwide Vehicle CoverageAccessoriesAdapter Cable, Carrying Case, Software Disc, USB Cable, User GuideUnit TypeUnitAdvantage 2All Systems +28 Reset Functions Free28 Special Functions(3)SAS, Airbag Reset, Injector Coding, ABS BleedingAdvantage 1One-Click UpdateOBD InterfaceCAN, EOBD, OBD, OBDIIFeaturesBacklit Display, Built-In Battery, Check Engine Light Shut Off, Color Display, Erases Codes, Freeze Frame Displays, Internet Updateable, LCD Display, Multi-Language Interface, User Friendly28 Special Functions(1)Oil Reset, Throttle Matching, EPB,MBSAdvantage 3Keypad & Touchscreen OperationUnit Quantity1Software cost99USD/year (Free for the first 3 years)28 Special Functions(5)Gearbox Matching, Sunroof InitializationWarranty5 YearDisplay7-inch LCD capacitive touchscreenVehicle TypePassenger VehicleManufacturer Part NumberMUCAR VO7SBrandMUCARSupported SystemABS, DPF, EPB, SAS, SRS, TPMS, Full systemROM32GBTypeProfessional Car Diagnostic ScannerConnectivityBluetooth28 Special Functions(2)Suspension Calibration, and Tyre Setting, Stop/StartCountry/Region of ManufactureChina28 Special Functions(6)Coolant Bleed, EGR Adaption, Gear LearningRAM2G28 Special Functions(4)DPF reset, Anti-Theft Matching, TPMS Resetsoftware update3 Years Free UpdateOperating SystemAndroid 10

Continue lendo2024 MUCAR VO7S Bidirectional Car Diagnostic Scanner Tool Key Coding CANFD OBD2

MUCAR VO7 OBD2 Scanner Bidirectional Car Diagnostic Tool All System ECU Coding

  • Autor do post:
  • Post publicado:
  • Categoria do post:
  • Comentários do post:0 comentário

ThinkOBD500MUCAR BT200MUCAR CDE900 PROTHINKTOOL MINI2MUCAR CS6MUCAR VO8THINKSCAN PLUS S7My store categoryCar Code readerThinkcar Scan toolBi-directional ScannerMUCAR Scan toolMUCAR CSBluetooth Car ScannerHot sale in storeMUCAR VO7 Auto OBD2 Scanner Full System Car Diagnostic Scanner Tool Key Coding329.00 USDThinktool mini OBD2 Scanner All System Diagnostic Tool Key Coding Bidirectional300.00 USDTHINKCAR Auto All System Diagnostic Tool Bidirectional Scanner Key Coding CANFD300.00 USDMUCAR VO8 OBD2 Scanner Key Coding All System Diagnostic Tool Bidirectional610.99 USDMUCAR VO7 OBD2 Scanner Code Reader Bidirectional Car Diagnostic Tool All SystemWhy You Need MUCAR VO7?【2024 Newest All-in-one Scanner】As the upgraded version of MUCAR VO6,The VO7 Car Diagnostic Scanner Provide ➤ Functional Tests & Bi-Directional Controls ➤Flash Hidden & VAG Guide Functions ➤【AutoAuth for FCA SGW】Works For Chrysler,For Dodge,and For Jeep after 2017 ➤ Setting & Changeover (adblue reset, unlock the engine after a collision, cancel ABS driving test, and more) for Benz ➤ Modification for BMW ➤ Customization ➤Personalization ➤ ECU Coding & Configurations ➤ 106+ Car Brands, and keep growing.【Bi-Directional Control/Active Tests】 The MUCAR VO7 bidirectional scan tool can output commands to a vehicle’s ECUs, read the ECU data, and monitor the operation of the actuators. Through active tests on certain components, such as fuel pumps, a/c fan, inside mirrors, headlamps, windows, and horns, this bidirectional scanner will let you quickly know whether a specific system, component, or subsystem is functioning properly or not, helping you locate the car issues precisely.【ECU Coding + Adaptation + Initialization + Matching】The MUCAR VO7 bidirectional obd2 scanner support ECU Coding to quickly match, learn, code any replaced ECU. Modify ECU and reveal hidden features for 99% cars in the market. Adaptive data for certain components after repairs or replacements.【28+ Maintenance Reset Functions】1.Throttle 2.Injector Coding 3. SAS 4. ABS 5. Oil 6. Gearbox 7. IMMO/Key Programming 8. Airbag 9. TPMS 10. Gear Learning 11. EPB 12. AFS 13. A/F 14. AdBlue 15. DPF 16. NOx Reset 17. EGR Bleed 18.IC 19. Coolant Bleed 20.Suspension 21. Tyre Setting 22. Seat Calibration 23.Windows Calibration 24.Sunroof 25. Language Set 26. Transport Mode 27. Stop/Start 28. BMS Note:Service functions vary by vehicle, please to check compatibilitybefore order‼【All Systems & Subsystems Diagnosis】The MUCAR VO7 OBD2 scanner diagnostic tool will automatically scan your entire vehicle's systems and subsystems including Body, Chassis, Powertrain, Fuel system, Light system, etc. It identifies systems and subsystems module information, reads fault codes, and generates a diagnostic report in as little as 120 seconds. You can access the system from the report menu to clear fault codes and live data graph,quickly locate vehicle faults and get them solved.【Intelligent Software to Keep Growing】MUCAR VO7 automotive diagnostic tool has powerful software ➤ Localized 17 Languages ➤ Coveage List ➤ AutoSearch Diagnose ➤ History Records ➤ Report Management ➤ OTA Upgrade ➤ 106+ Vehicle Brands Software to Keep Growing, VO7 scanner for car works on most OBD-II compliant cars after 1996 and upgrade new make up to 2022 models, compatible with OBD2/EOBD & CAN protocols, including most 12v cars, SUV, pickup, light duty truck, minivans.【Wireless & Bluetooth + High-End Configuration】The VO7 car scanner equipped with the powerful 1.8GHz processor, Android 10.0, 7”touchscreen, 32G ROM, 6000mAh battery,2.4GHz & 5GHz Wi-Fi connection;With the included Bluetooth 4.0 VCI dongle, experience wireless diagnostics with an operating range of up to 33 feet (10 meters).【Buy with Confidence:2-Year Warranty & 100% Original 】To make your purchase worry-free, this 100% original MUCAR scanner - The VO7 comes with 30-day free refunds and exchanges;If you think you receive an used or defective product,Please don't worry and contact us! If you are not pleased with your VO7 code reader and choose to return it, please kindly mark it unsellable to avoid an used one is resold again to other customers. Appreciate very muc Product Homepage Function 1. Intellignt diagnosis, automatic identification of vin, enter the diagnosis system 2. Maintenance service, maintenance service download, enter the system 3. MUCAR mall, subscription software, software upgrade, realize full-function diagnosis 4. Online upgrade , The software version can be updated 5. Vehicle files, save the data records of the detected vehicles, such as: report 6. Settings Intelligent diagnosis Insert the connector into the vehicle OBD interface, and the host can be connected to the connector. In the intelligent diagnosis mode, it can automatically read the vin identification vehicle information. If the special vehicle cannot be identified, the vehicle can also be manually selected for detection. After entering the system, the basic functions of the whole system of the vehicle can be tested (not including: action test, special function, cding), code reading, code clearing, real-time data flow chart display, combined display can be performed. Support obd full-function intelligent diagnosis. Purchase a model software separately, which can be upgraded to full-system full-function. MUCAR VO7 supports full system functionality, including bidirectional functions, ECU coding, and other special functions. Free use of full functionality within 3 years, with a follow-up fee of $99 per year for 3 years.​ Support to ECU Coding The Coding function is used to re-flash the vehicle control modules.It is used to reprogram adaptive data for vehicle control modules after repairs or replacements of vehicle parts;Provide solutions for the issues of Drivability, Fuel Efficiency, Power Loss, Fault Codes, Durability of Mechanical Parts etc.;Brake the limitations and restrictions; make full use of the car hidden features, like change the chimes on car, set how many times the one-touch signal flickers for one touch, remember settings for Start/Stop systems, and more. Support Active Test (Actuation Test) If the actuator is normal, without using the vehicle’s controls, to get a significant boost in effectiveness: [ Turn on the radiator fan | Modulate the throttle | Open/close windows | Operate mirrors | Turn on/off the lights | Turn on/off the sound horn | Test door lock … ] MUCAR VO7 Lifetime Free All Cars Full System Diagnostic TOOL: With superior all systems diagnoses, this multipurpose obd2 scanner can be used to read all available systems’ECU information to facilitate the vehicle diagnosis.The complete systems vary from different cars and they usually include engine, transmission, ABS, SRS, SAS, TPMS, EPB and chassis / body / electrical equipment system etc. ✅Examinate your car like a professional mechanical technician ✅Read DTCs from the vehicle’s all electronic control systems to locate problem areas, and offer solutions; ✅Erase the codes easily after DTCs retrieving and certain repairs have been carried out and turn off fault Indicator lamp; ✅Live data shows each sendor parameter item displayed in analog, text, waveform graph modes etc ✅The active test used to access vehicle-specific subsystem and component tests. MUCAR VO7 Lifetime Free All Cars 28 Reset Services 1. Oil Reset The lightening of the car maintenance light indicates that the vehicle needs maintenance.Reset the mileage or driving time to zero after the maintenance, so the maintenance light will go out and the system will start a new maintenance cycle. 2. Elec.Throttle Adaption Elec. Throttle Adaption is to utilize the car decoder to initialize the throttle actuator so that the learning value of the ECU returns to the initial state. 3.Steering Angle Reset To reset the steering angle, first find the relative zero point position for the car to drive in straight line.Taking this position as reference,the ECU can calculate the accurate angle for left and right steering. 4. Battery Matching This function enables you to perform a resetting operation on the monitoring unit of vehicle battery, in which the original low battery fault information will be cleared and battery matching will be done. 5. ABS Bleeding When the ABS contains air, the ABS bleeding function must be performed to bleed the brake system to restore ABS brake sensitivity. 6.Break-pad Reset lf the brake pad wears the brake pad sense line, the brake pad sense line sends a signal sense line to the on-board computer to replace the brake pad.After replacing the brake pad, you must reset the brake pad.Otherwise, the car alarms. 7.DPF Regeneration DPF regeneration is used to clear PM(Particulate Matter) from the DPF filter through continuous combustion oxidation mode (such as high temperature heating combustion, fuel additive or catalyst reduce PM ignition combustion) to stabilize the filter performance. 8.Gear Learning After the engine ECu, crankshaft position sensor,or crankshaft flywheel is replaced, or the DTC 'gear not learned' is present, gear learning must be performed. 9. IMMO Service To prevent the car being used by unauthorized keys, the anti-theft key matching function must be performed so that the immobilizer control system on the car identifies and authorizes remote control keys to normally use the car. 10. Injector Coding Write injector actual code or rewrite code in the ECU to the injector code of the corresponding cylinder so as to more accurately control or correct cylinder injection quantity. 11.TPMS Reset Note:Cooperate with wireless tire pressure diagnosis tool to realize TPMS activation, programming and learning functions 12. Suspension Matching This function can adjust the height of the body. When replacing the body height sensor in the air sus pension system, or control module or when the vehicle level is incorrect, you need to perform thisfunction to adjust the body height sensor for level calibration. 13. AFS Reset This feature is used to initialize the adaptive headlamp system. 14.A/T Learning This function can complete the gearbox self-learning to improve gear shifting quality. 15.Sunroof Initialization This function can set the sunroof lock off, closed when it rains,sliding /tilting sunroof memory function,temperature threshold outside the car etc. 16. EGR Adaption This function is used to learn the EGR valve after it is cleaned or replaced. 17. ODO Reset ODO reset is to copy, write, or rewrite the value of kilometers in the chip of odometer by using a car diagnostic computer and data cable, so that the odometer shows the actual 18. Airbag Reset This function resets the airbag data to clear the airbag collision fault indicator. 19. Transport Mode ln order to reduce power consumption, the following functions may be disabled, including limiting the vehicle speed, not waking up the door opening network, and disabling the remote control key, etc.At this time, the transport mode needs to be deactivated to restore the vehicle to normal. 20. A/F Reset This function is applied to set or learn Air/Fuel ratio parameters. 21. Stop/Start Reset This function is used to open or close the automatic start-stop function via setting the hidden function in ECU(provided that the vehicle has a hidden function and supported by hardware). 22. NOx Sensor Reset NOx sensor is a sensor used to detect the content of nitrogen oxides (NOx) in engine exhaust. lf theNOx fault is re-initialized and the NOx catalytic converter is replaced, it is necessary to reset the catalytic converter learned value stored in the engine Ecu. 23. AdBlue Reset (Diesel Engine Exhaust Gas Filter) After the diesel exhaust treatment fluid (car urea) is replaced or filled up, urea reset operation is required. 24.Seat Calibration This function is applied to match the seats with memory function that are replaced and repaired. 25.Coolant Bleeding Use this function to activate the electronic water pump before venting the cooling system. 26.Tyre Reset This function is used to set the size parameters of the modified or replaced tire. 27.Windows Calibration This feature is designed to perform door window matching to recover ECU initial memory, and recover the automatic ascending and descending function of power window. 28. Language Change This function is used to change the system language of the vehicle central control panel. Free Full OBDII Functions *-Read extensive current, pending and permanent codes in OBD system quickly *-Clear detected fault codes and turn off the Check Engine Light efficiently *-View graphical live data of vehicle's computer module(s) for easy analyses *-View the vehicle's operating parameters at the moment a DTC is detected *-Read I/M readiness status to have a vehicle inspected for state emissions compliance *-Perform O2 sensor test to check fuel efficiency and vehicle emissions *-Read the results of on-board diagnostic monitoring tests for specific components/systems *-Retrieve the vehicle information of VIN, CINs, and CVNs completely *-Perform the component Test by allowing initiating a leak test for the vehicle's EVAP system 4 IN 1 Scientific Data Management: Live Data Stream Graph & Record Data & Diagnosis Record Playback & Print Report The professional vehicle scanner tool can scientific graph data, record data, play back data, freeze frame,and print reports. In the real-time diagnosis process, important diagnosis information can be instantly stored in the memory, including reading of fault codes and frozen frames and real-time data streams. After real-time diagnosis is completed, Diagnosis function record playback, the diagnosis information and process previously saved in the memory can be replayed to facilitate the analysis of various data information. One-click generation of a diagnosis report after diagnosis will help users quickly solve problems, avoid blind maintenance, and save money/time. MUCAR VO7 Support 20 Multi-Langauge English, French, German, Italian, Spanish, Portuguese, Japanese, Russian, Polish language, Hungarian language, Arabic, Greek, Slovakia, Dutch language, Korean, Turkish language, Czech ,Indonesian Support 128+ Worldwide Vehicle Coverage Support 126+ Car Brands and 1000+ Vehicles USA: For BXGM,For CHRYSLER, For AUSTFORD, For GM,USAFORD EUROPE: For ASTONMARTIN,For AUDI,For BENZ,For BMW,For BXFIAT,For CITROEN,For FERRARI,For FIAT,For GAZ,For LANDROVER,For MASE,RATI,For OPEL,For PAZ,For PEUGEOT,For PORSCHE... Austrillia: For AUSTFORD,For AUSTHOLDEN Asia: For BAIC,For CHANGAN,For CHANGCHENG,For CHANGHE,For DAEWOO,For DAIHATSU,For DFXK,For FLYER,For FUTIAN,For HAFEL For HMAZDA,For HONDA,For HUACHEN,For HYUNDAI,For IKCO,For INDIANMARUTI,For INDIANTATA,For ISUZU,For IVECO.IZH,For JACTY JIAO,For JINLONG,For JOYLONG,For JPISUZU,KIA,For LIFAN, For LIUWEITY ,For LUXGEN,For MAHINDRA,For MALAYSIA PERODUA,For MALAYSIA PROTON,For MARUT,For MAXUS,For MAZDA,For MITSUBISHI... How to Register/Update MUCAR VO7 1.Initial Use 2.Turn on the Machine 3.Language Setting 4.Connect WIFI 5.Choose Time Zone 6.User Agreement 7.Create an Account 8.Typing in Business Information Product Parameters: Display Screen :7-Inch/TFT(IPS) Connection :Wi-Fi/Bluetooth RAM:2G ROM:32G Working Temperature : 32℉~122℉ Storage Temperature: -4℉~144℉ Packing List: 1*MUCAR VO7 Host 1*Diagnostic dongle 1*Charging cable 1*Multi-Language ManualMUCAR VO8MUCAR VO7SMUCAR VO7MUCAR VO6THINKCAR Thinktool miniAdvantage-1Full System Diagnosis For FreeFull System Diagnosis For FreeFull System Diagnosis For FreeFull System Diagnosis For FreeFull System Diagnosis For FreeAdvantage-234+ Reset Services28+ Resets Functions28+ Resets Functions28+ Resets Functions28+ Resets FunctionsAdvantages 3Bidirectional FreeBidirectional FreeBidirectional FreeBidirectional (pay for $49.95)Bidirectional (pay for $49.95)Battery9450mAh6300mAh6300mAh6300mAh6300mAhBrandMUCARMUCARMUCARMUCARThinkCarDisplay8 inch Touch Screen7 inch Touch Screen7 inch Touch Screen5.99 inch Touch Screen5.99 inch Touch Screensupported protocolsISO 14230-4 KWP/ 15765-4 CAN/ ISO 9141-2IS0/ SAE J1850 VPW/ SAE J1850 PWMCANFD Protocol/ ISO 14230-4 KWP/ 15765-4 CAN/ ISO 9141-2IS0/ SAE J1850 VPW/ SAE J1850 PWMISO 14230-4 KWP/ 15765-4 CAN/ ISO 9141-2IS0/ SAE J1850 VPW/ SAE J1850 PWMISO 14230-4 KWP/ 15765-4 CAN/ ISO 9141-2IS0/ SAE J1850 VPW/ SAE J1850 PWMISO 14230-4 KWP/ 15765-4 CAN/ ISO 9141-2IS0/ SAE J1850 VPW/ SAE J1850 PWMLanguagesSupport 28 LanguagesSupport 19 LanguagesSupport 19 LanguagesSupport 20 LanguagesSupport 17 LanguagesMemory2GB + 64GB2GB + 32GB2GB + 32GB2GB + 32GB2GB + 32GBOBD InterfaceCAN, EOBD, OBD, OBDIICAN, EOBD, OBD, OBDIICAN, EOBD, OBD, OBDIICAN, EOBD, OBD, OBDIICAN, EOBD, OBD, OBDIISupported SystemFull System, ABS, DPF, EPB, SAS, SRS, TPMS, EngineFull System, ABS, DPF, EPB, SAS, SRS, TPMS, EngineFull System, ABS, DPF, EPB, SAS, SRS, TPMS, EngineFull System, ABS, DPF, EPB, SAS, SRS, TPMS, EngineFull System, ABS, DPF, EPB, SAS, SRS, TPMS, EngineUpdate2-year free update3-year free update3-year free updatelifetime free Updatelifetime free UpdateOperating systemAndroid 8.0Android 10.0Android 10.0Android 10.0Android 10.0Warranty5 Years5 Years5 Years5 Years5 YearsPaymentDelivery detailsReturn detailsAbout usContact usPaymentWe accept the following payment methods To ensure that your items can be delivered as soon as possible, please fill in your payment information accurately! Thank youDelivery details All the products in my shop have local warehouses in the United States, Britain, France, Germany, and Australia. U.S. warehouses: They are located in two warehouses in New Jersey and California, both of which can be shipped within 1 day and delivered within 5 days. Australian warehouse: located in Sydney, we use Australia Post or fastways express delivery, and the products can be delivered within 3-7 days. UK warehouse, with self-built warehouse in Wolverhampton and stock in official ebayg warehouse, both can be delivered within 2 days . German warehouse, we use eBay official warehouse, there is sufficient inventory, and can be sent to 28 EU countries. It can be shipped the same day the order is placed, and delivered within two days within Germany. Return details We accept the following return methods Returns are accepted within 30 days of buyer receiving the item. (Does not include man-made damage or misuse). 100% Money Back Guarantee! All products will be 100% tested before shipping. Buyer has up to 30 days from date of receipt for replacement if item is defective due to postage handling. All shipping costs for returned products are paid by the seller, please contact us for the return address For any questions about defects, returns, item exchange requests, please contact us and send us a message before opening any kind of case or request. We are committed to making every customer 100% satisfied and solving any problems. We highly value and appreciate your business. Thanks. Returns are accepted within 30 days of delivery. Returned items must be in new, unaltered and resalable condition. Seller is not responsible for any labor costs, dealer store fees, or damage caused by incorrect installation.About us THINKCAR has an intelligent production workshop, which covers an area of more than 3,500 square meters, is equipped with a fully automatic packaging production line, and has intelligent warehouse management. THINKCAR products have gone through more than 50 production processes, passed 2 meters, 3 meters and other height drop tests, -4℉-140℉ high and low temperature tests, 8 hours vibration test, 1000 plug-in tests, 1000 circular wire throwing tests, Continuous working test for more than 48 hours, real vehicle test of more than 100 car brands, including most popular models in Europe, America and Asia. As the official store of Thinkcar, all products are 100% original products. THINKCAR is a company specializing in automotive diagnostic tools, committed to providing quality products and services. Contact us(1) We maintain high standards of excellence 5 Star feedback and strive for 100% Customer satisfaction. Please do not hesitate to leave us your positive feedback if you are satisfaction with our products ,delivery or services .(2)If you have any questions about our products or services, Please Contact usimmediately before you leave Neutral or Negative feedback,So that we can satisfactorily address your concerns. We will reply you within 12 hours, except on Weekends and Holidays.(3)If you have any needs for products, please contact us ,we’ll do our best solve with you . 4Solve any problems with you in friendly way after communication. Refund or Replacement will be provided as you like.Memory2+32GBAccessoriesAdapter Cable, User Guide, Carrying Case, Software Disc, USB CableUnit TypeUnitVersion2024 NewestFunction 3Bidirectional test, action testing, ECU CODING28 Special Functions(3)SAS, Airbag Reset, Injector Coding, ABS BleedingFunction 2Full System Diagnostic + 28 reset FunctionsOBD InterfaceCAN, EOBD, OBD, OBDIIFeaturesBacklit Display, Built-In Battery, Check Engine Light Shut Off, Color Display, Erases Codes, Freeze Frame Displays, Internet Updateable, LCD Display, Multi-Language Interface, User FriendlyFunction 1Wireless & Bluetooth + AUTOVIN28 Special Functions(1)Live Data Display & Diagnostic FeedbackUnit Quantity128 Special Functions(7)AFS Headlight Reset, A/F Reset, Seat CalibrationFunction 63 years Free updateSoftware cost99USD/year for update (Free for the first 3 years)TYPEprofessional car scanner diagnostic toolFunction 5Support 28 Resets28 Special Functions(5)Gearbox Matching, Sunroof InitializationOperating systemAndroid 10.0Function 4Support 20 LanguagesBuilt-in battery6000mAhWarranty3 YearVehicle TypePassenger VehicleManufacturer Part NumberDoes Not ApplyBrandMUCARSupported SystemABS, DPF, EPB, TPMS, SRS, SAS, Full systemsScreen size7 Inch Touch ScreenConnectivityBluetooth28 Special Functions(2)Suspension Calibration, and Tyre Setting, Stop/StartCountry/Region of ManufactureChina28 Special Functions(6)Coolant Bleed, EGR Adaption, Gear Learning28 Special Functions(4)DPF Reg., Anti-Theft Matching, TPMS ResetUPC724190795408

Continue lendoMUCAR VO7 OBD2 Scanner Bidirectional Car Diagnostic Tool All System ECU Coding